Re: Installed Svc Pack - STRCODE No Work

["Wayne Achenbaum" <wache@xxxxxxxxxxx>]

Jeff I am having the same problem after installing Sp1 V4R5M1. At first when
I did a strcode with no parms entered it appeared an interactive strcode
session was started. I tried to prompt a cl command in the code editor and
it told me I needed an interactive strcode session active and it appeared I
did. Then I went to the properties of the communications Daemon and filled
in on the strcode settings the remote location name which was blank and used
to work. Now I get the same message as you and additionally I can not bring
up the properties on the communications Daemon anymore. It appears to me
there are some problems in Sp1.


 Below is my Joblog error Message:

 Message ID . . . . . . :   EVF4100       Severity . . . . . . . :   10
 Message type . . . . . :   Information
 Date sent  . . . . . . :   01/16/01      Time sent  . . . . . . :
17:25:45

 Message . . . . :   Default information for STRCODE retrieved successfully.
 Technical description . . . . . . . . :
 - The default information has been retrieved from *LIBL/STRCODE *USRSPC.
 - The server name is FORSYTE2.
 - The communications type is *TCPIP.
 - The APPC remote location name is .
 - The TCP/IP remote location name is 192.1.1.182.
 - The TCP/IP port is 4200.
Wayne
----- Original Message -----
From: Jeff Crosby <jlcrosby@fwi.com>
To: <code400-l@midrange.com>
Sent: Monday, January 15, 2001 4:42 PM
Subject: Installed Svc Pack - STRCODE No Work


> I installed SP1 for WDT V4R5M1 today.  Since then the STRCODE command will
not
> work.  I get the following in the job log:
>
>                         Additional Message Information
>
> Message ID . . . :   EVF4000       Severity . . . . :   30
> Message type . . :   Diagnostic
> Date sent  . . . :   01/15/01      Time sent  . . . :   16:13:33
>
> Message . . . . :   A TCP/IP communications error occurred.
> Cause . . . . . :   A route to the remote host is not available.
> - The name of the error is ERR_TCPIP (3429).
> - The name of the function is ipClientConnect-connect.
>
> The prior job log message was:
>
>                          Additional Message Information
>
> Message ID . . . :   EVF4100       Severity . . . . :   10
> Message type . . :   Information
> Date sent  . . . :   01/15/01      Time sent  . . . :   16:13:3
>
> Message . . . . :   Default information for STRCODE retrieved
successfully.
> Technical description . . . . . . . . :
> - The default information has been retrieved from *LIBL/STRCODE *USRSPC.
> - The server name is AS400.
> - The communications type is *TCPIP.
> - The APPC remote location name is *ICFF.
> - The TCP/IP remote location name is 4.0.0.3.
> - The TCP/IP port is 4200.
>
>
>
>
>
>
>
> --
> -Jeff
> The opinions expressed are my own and not necessarily
> the opinion of my company.  Unless I say so.
> +---
> | This is the CODE/400 Mailing List!
> | To submit a new message, send your mail to CODE400-L@midrange.com.
> | To subscribe to this list send email to CODE400-L-SUB@midrange.com.
> | To unsubscribe from this list send email to
CODE400-L-UNSUB@midrange.com.
> | Questions should be directed to the list owner/operator: larry@paque.net
> +---

+---
| This is the CODE/400 Mailing List!
| To submit a new message, send your mail to CODE400-L@midrange.com.
| To subscribe to this list send email to CODE400-L-SUB@midrange.com.
| To unsubscribe from this list send email to CODE400-L-UNSUB@midrange.com.
| Questions should be directed to the list owner/operator: larry@paque.net
+---