This may be as far as I can go toward helping without dumping the print
stream.
You might check the device description of the printer and make sure it
is all coordinated with your printer. Auto-gen'd device descriptions are
sometimes wrong.
Is sysval QCCSID 37?
Contents of the MoDCA barcode tag generated by the print file may be
translated at a different point in the workflow than the rest of the
text. Your print file generates MoDCA AFP. The print writer uses the
device description to convert that stream to IPDS. The printer reads the
IPDS and rasterizes it to the paper. Anything can be a problem. IPDS is
a bi-directional data stream. I've heard of these things breaking when
the network blocked the back-channel.
-----Original Message-----
From: midrange-l-bounces@xxxxxxxxxxxx
[mailto:midrange-l-bounces@xxxxxxxxxxxx] On Behalf Of
Wim_Vandepoel@xxxxxxx
Sent: Thursday, June 04, 2009 8:34 AM
To: Midrange Systems Technical Discussion
Subject: RE: 2D DataMatrix Barcode Error
Thanks for the reply Dan,
Here is what I can find about code pages and CCSID's...
- the printer default code page is Int. Set 5 500
- the job's default code page is 37
- the printer file has *DEVD as character identifier
- the device character identifier is *SYSVAL
According to the manual, the system extracts the ccsid of the job that
generates the spool file and translates EBCDIC data to code page 500.
The printer then translates the data from code page 500 to the
appropriate ASCII code page.
Did I miss something?
FWIW, I get the same errors on V5R4.
Wim
"Dan Kimmel" <dkimmel@xxxxxxxxxxxxxxx>
Sent by: midrange-l-bounces@xxxxxxxxxxxx
03/06/2009 20:11
Please respond to
Midrange Systems Technical Discussion <midrange-l@xxxxxxxxxxxx>
To
"Midrange Systems Technical Discussion" <midrange-l@xxxxxxxxxxxx>
cc
Subject
RE: 2D DataMatrix Barcode Error
The message is that the printer refused to print the barcode. Most
likely due to a character that the barcode doesn't support. Datamatrix
promises to print any ASCII character. So somewhere the EBCDIC to ASCII
is not producing a valid ASCII character representation. IPDS is usually
a EBCDIC stream to the printer, but that depends on how your printer
definition is configured. In that case, printer should be doing whatever
character translation is necessary to produce the barcode. The printer
firmware is rasterizing the bitmap for the barcode and should know its
own EBDCIC to ASCII translation.
Examine the CCSID of your print file and see if that matches the CCSID
the printer expects. I'm guessing you are someplace where everything is
not 37.
-----Original Message-----
From: midrange-l-bounces@xxxxxxxxxxxx
[mailto:midrange-l-bounces@xxxxxxxxxxxx] On Behalf Of
Wim_Vandepoel@xxxxxxx
Sent: Wednesday, June 03, 2009 2:03 AM
To: midrange-l@xxxxxxxxxxxx
Subject: 2D DataMatrix Barcode Error
Hi All,
I am trying to print a 2D Datamatrix Barcode with an IPDS printer
(infoprint 1552).
The data to print consists of address pieces seperated by a pipe.
If I only use upper case or lower case, numbers and spaces, the barcode
prints out fine.
If I combine upper and lower, or if I use a pipe or other characters
like comma, dot, slash, ampersand...
I get the following error:
Message ID . . . . . . : PQT3665, Bar Code Specification Check
exception.
Message ID . . . . . . : PQT3630, Sense data X'040C0100 DE000001
00000000 D6810000 00000000 00000001' was received
Here is the DDS code:
A GLS8902 127A
A BARCODE(DATAMATRIX 1 +
A (*DATAMATRIX 36 36))
A POSITION(3.3 0.6)
We are at v5r3.
Any idea why I can not print those characters?
Could it be a translation error?
Best Regards
Wim
--
This is the Midrange Systems Technical Discussion (MIDRANGE-L) mailing
list To post a message email: MIDRANGE-L@xxxxxxxxxxxx To subscribe,
unsubscribe, or change list options,
visit:
http://lists.midrange.com/mailman/listinfo/midrange-l
or email: MIDRANGE-L-request@xxxxxxxxxxxx Before posting, please take a
moment to review the archives at
http://archive.midrange.com/midrange-l.
As an Amazon Associate we earn from qualifying purchases.