× The internal search function is temporarily non-functional. The current search engine is no longer viable and we are researching alternatives.
As a stop gap measure, we are using Google's custom search engine service.
If you know of an easy to use, open source, search engine ... please contact support@midrange.com.


  1.  Home
  2. MIDRANGE-L
  3. June 2006

RE: TCP/IP tuning

Sorry that's wrksysval *all *print

-----Original Message-----
From: midrange-l-bounces@xxxxxxxxxxxx
[mailto:midrange-l-bounces@xxxxxxxxxxxx] On Behalf Of Don Cavaiani
Sent: Thursday, June 08, 2006 9:59 AM
To: Midrange Systems Technical Discussion
Subject: RE: TCP/IP tuning

What happens if the VRYCFG *OFF is issued and there are some Iseries
users telneted (Mochasoft client) into the system at that time? 

-----Original Message-----
From: midrange-l-bounces@xxxxxxxxxxxx
[mailto:midrange-l-bounces@xxxxxxxxxxxx] On Behalf Of Kevin Parrett
Sent: Thursday, June 08, 2006 9:41 AM
To: 'Midrange Systems Technical Discussion'
Subject: RE: TCP/IP tuning

O.K. I think the line was active or vary on pending prior to the call of
QSTRUP. Your program is correct and should have changed the line. With
the monmsg cpf000 it would have continued normally. Without changing the
line.
Have you looked in QEZJOBLOG outq for a print relating to this? A way to
solve this would be to:

Vrycfg ethline01 *off
Chglineth duplex(*full)
Vrycfg ehtine01 *on

Then continue . . . 

Am I correct in assuming that your user cannot afford 5 minutes of down
time? That's really all the time it takes to do what you need.
Kevin


-----Original Message-----
From: midrange-l-bounces@xxxxxxxxxxxx
[mailto:midrange-l-bounces@xxxxxxxxxxxx] On Behalf Of Don Cavaiani
Sent: Thursday, June 08, 2006 9:25 AM
To: Midrange Systems Technical Discussion
Subject: RE: TCP/IP tuning

Kevin - It was recompiled on 6/1,  and shows run ONE time, early this
morning 6/8.  I do not see any particular message in the Q. 

-----Original Message-----
From: midrange-l-bounces@xxxxxxxxxxxx
[mailto:midrange-l-bounces@xxxxxxxxxxxx] On Behalf Of Kevin Parrett
Sent: Thursday, June 08, 2006 9:06 AM
To: 'Midrange Systems Technical Discussion'
Subject: RE: TCP/IP tuning

Sounds Like the program you listed did not run. Is your system value
wrksysval QSTRUPPGM. The program should be compiled into the library
shown here. There should also be a message or 2 in the qsysopr msgq that
may point you to a resolution.
Kevin  

-----Original Message-----
From: midrange-l-bounces@xxxxxxxxxxxx
[mailto:midrange-l-bounces@xxxxxxxxxxxx] On Behalf Of Don Cavaiani
Sent: Thursday, June 08, 2006 6:19 AM
To: Midrange Systems Technical Discussion
Subject: RE: TCP/IP tuning

I see that the LINE description still shows online at IPL *NO, so the
CHGLINETH command did not run ?? 

-----Original Message-----
From: midrange-l-bounces@xxxxxxxxxxxx
[mailto:midrange-l-bounces@xxxxxxxxxxxx] On Behalf Of Don Cavaiani
Sent: Thursday, June 08, 2006 6:12 AM
To: Midrange Systems Technical Discussion
Subject: RE: TCP/IP tuning

The IPL went last night, but I am still showing only HALF Duplex?

Below is the modified CL which shows that it has been USED one time.  I
checked the logs, but nothing seems to indicate that there was an error
in any of the commands.

/********************************************************************/  
     PGM                                                                
     MONMSG MSGID(CPF0000)                                              
/********************************************************************** 
     CHGLINETH  LIND(ETHLIN01) ONLINE(*YES) DUPLEX(*FULL)               
     MONMSG MSGID(CPF0000)                                              
     VRYCFG CFGOBJ(ETHLIN01) CFGTYPE(*LIN) STATUS(*ON)                  
                                                  
/********************************************************************** 
                                                           
     STRSBS QSERVER                                                     
     STRSBS SBSD(QSYS/QCTL)                                             
     STRSBS SBSD(AMESYS/QSPL)                                           
     STRSBS SBSD(AMESYS/QSNADS)                                         
     STRCLNUP                                                           
     STRPRTWTR DEV(*ALL)                                                
     STRSBS SBSD(AMESYS/QBATCH)                                         
     STRSBS SBSD(AMESYS/QCMN)                                           
     STRSBS SBSD(AMESYS/QINTER)                                         
     STRSBS SBSD(QPGMR)                                                 
                           
     DLYJOB     DLY(120)                                                
     STRTCP                                                             
                                                  
                                                            
     DLYJOB     DLY(120)                                                
     STRHOSTSVR *ALL                                                    
                                                 
                                                                        
     ENDPGM


-----Original Message-----
From: midrange-l-bounces@xxxxxxxxxxxx
[mailto:midrange-l-bounces@xxxxxxxxxxxx] On Behalf Of Sean Porterfield
Sent: Thursday, June 01, 2006 8:48 PM
To: Midrange Systems Technical Discussion
Subject: Re: TCP/IP tuning

Also, your MONMSG commands should be after each of the commands you run
instead of before.  Since you already have a MONMSG CPF0000 at the
beginning, it will apply to the whole program making your others
redundant.

--
Sean Porterfield

Chris Bipes wrote:

Move it to the beginning.  TCP will not start completely with out the 
line up and running.  I would put it between 2900 and 3000


Christopher Bipes
Information Services Director
CrossCheck, Inc.


-----Original Message-----
From: Don Cavaiani
Sent: Thursday, June 01, 2006 10:04 AM



I added lines 4900 through 5200 ...  

2600-
/********************************************************************
2700-      PGM

2800-      MONMSG MSGID(CPF0000)

   2900- /* A458A */

   3000-      STRSBS QSERVER

   3100-      STRSBS SBSD(QSYS/QCTL)

   3200-      STRSBS SBSD(AMESYS/QSPL)

   3300-      STRSBS SBSD(AMESYS/QSNADS)

   3400-      STRCLNUP

   3500-      STRPRTWTR DEV(*ALL)

   3600-      STRSBS SBSD(AMESYS/QBATCH)

   3700-      STRSBS SBSD(AMESYS/QCMN)

   3800-      STRSBS SBSD(AMESYS/QINTER)

   3900-      STRSBS SBSD(QPGMR)

                            
   4500- /* A458A */

   4600-      DLYJOB     DLY(120)

   4700-      STRTCP

   4800-      MONMSG MSGID(CPF0000)
______________________________________________________________________

   4900-      MONMSG CPF0000

   5000-      CHGLINETH  LIND(ETHLIN01) ONLINE(*YES) DUPLEX(*FULL)

   5100-      MONMSG CPF0000

   5200-      VRYCFG CFGOBJ(ETHLIN01) CFGTYPE(*LIN) STATUS(*ON)
______________________________________________________________________

   5300- /* A458A */

   5400-      DLYJOB     DLY(120)

   5500-      STRHOSTSVR *ALL

   5600-      MONMSG MSGID(CPF0000)

   5700-

                                     
   6000-      ENDPGM

--
This is the Midrange Systems Technical Discussion (MIDRANGE-L) mailing
list To post a message email: MIDRANGE-L@xxxxxxxxxxxx To subscribe,
unsubscribe, or change list options,
visit: http://lists.midrange.com/mailman/listinfo/midrange-l
or email: MIDRANGE-L-request@xxxxxxxxxxxx Before posting, please take a
moment to review the archives at http://archive.midrange.com/midrange-l.


--
This is the Midrange Systems Technical Discussion (MIDRANGE-L) mailing
list To post a message email: MIDRANGE-L@xxxxxxxxxxxx To subscribe,
unsubscribe, or change list options,
visit: http://lists.midrange.com/mailman/listinfo/midrange-l
or email: MIDRANGE-L-request@xxxxxxxxxxxx Before posting, please take a
moment to review the archives at http://archive.midrange.com/midrange-l.


--
This is the Midrange Systems Technical Discussion (MIDRANGE-L) mailing
list To post a message email: MIDRANGE-L@xxxxxxxxxxxx To subscribe,
unsubscribe, or change list options,
visit: http://lists.midrange.com/mailman/listinfo/midrange-l
or email: MIDRANGE-L-request@xxxxxxxxxxxx Before posting, please take a
moment to review the archives at http://archive.midrange.com/midrange-l.





--
This is the Midrange Systems Technical Discussion (MIDRANGE-L) mailing
list To post a message email: MIDRANGE-L@xxxxxxxxxxxx To subscribe,
unsubscribe, or change list options,
visit: http://lists.midrange.com/mailman/listinfo/midrange-l
or email: MIDRANGE-L-request@xxxxxxxxxxxx Before posting, please take a
moment to review the archives at http://archive.midrange.com/midrange-l.

As an Amazon Associate we earn from qualifying purchases.

This thread ...
Replies:
Follow On AppleNews
Return to Archive home page | Return to MIDRANGE.COM home page

This mailing list archive is Copyright 1997-2024 by midrange.com and David Gibbs as a compilation work. Use of the archive is restricted to research of a business or technical nature. Any other uses are prohibited. Full details are available on our policy page. If you have questions about this, please contact [javascript protected email address].

Operating expenses for this site are earned using the Amazon Associate program and Google Adsense.