× The internal search function is temporarily non-functional. The current search engine is no longer viable and we are researching alternatives.
As a stop gap measure, we are using Google's custom search engine service.
If you know of an easy to use, open source, search engine ... please contact support@midrange.com.



Pete,

I don't think I'd scratch the system till I got this sorted out. Without a
good display, you'll never be able to configure the console. If I remember
right, our 720 had two twinax bricks. Can you switch the one to the other
controller? Is the device description for DSP0100000 say CTL02 or CTL01? If
it's CTL01, can you change it to CTL02? And, are you sure the cable and
terminator are good?

Thanks,

Mark

Mark D. Walter
Senior Programmer/Analyst
CCX, Inc.
mwalter@xxxxxxxxxx
http://www.ccxinc.com


                                                                           
             Pete Helgren                                                  
             <Pete@xxxxxxxxxx>                                             
             Sent by:                                                   To 
             midrange-l-bounce         Midrange Systems Technical          
             s@xxxxxxxxxxxx            Discussion                          
                                       <midrange-l@xxxxxxxxxxxx>           
                                                                        cc 
             04/19/2005 12:21                                              
             PM                                                    Subject 
                                       Re: No signon screen                
                                                                           
             Please respond to                                             
             Midrange Systems                                              
                 Technical                                                 
                Discussion                                                 
             <midrange-l@midra                                             
                 nge.com>                                                  
                                                                           
                                                                           




OK, lots of suggestions. Let me see if I can sort through them all.

Mark:  I am not necessarily trying to get this guy to come up as a
console.  I'd just like to make sure I get a signon screen so that I
know everything is working OK BEFORE I scratch this thing.  I'd hate to
scratch install and not have a console at that point so what I am trying
to do is a reality check to make sure that when I really do need it, it
will come up.

Phil: When I do a PRTDEVADR on CTL02 I have a single 3476 device called
DSP010000.

Scott: No SRC codes. I tried changing the front panel to manual then set
the option to 21 and pressed enter (think that is what you meant by
forcing DST option 21).  No change.

Rob:

- If QCTLSBSD is set to QCTL, make sure that QINTER is running.

It is, and they have this thing configured with two interactive subsystems:
QINTER001 and QINTER002.  AS I recall they did this because they had, like,
1000 devices on QINTER and somehow it reached a maximum so they split the
subsystem in two.

- Check the station address on the terminal
Address is 0
- Check the port number that you are plugged into
Port is 0

- Check out that the workstation is varied on.

DSP010000 shows varied on.

QCONSOLE shows that DSP010000 is the console name.


More questions arise in my mind though.  The DSP010000 value as console
tells me that it was originally created on CTL01, correct?  CTL01 shows
a type of 266C.  CTL02 shows a type of 2722 and that is what the twinax
"brick" cable is connected to.  Perhaps they removed the original
hardware for CTL01? There is an empty slot in the back of this thing and
I don't see anything indicating a 266C on the back either.

I hate to just "try" a scratch install and hope that I get a console.  I
want to know all was well before I wipe it clean.....

Thanks,

Pete




--
This is the Midrange Systems Technical Discussion (MIDRANGE-L) mailing list
To post a message email: MIDRANGE-L@xxxxxxxxxxxx
To subscribe, unsubscribe, or change list options,
visit: http://lists.midrange.com/mailman/listinfo/midrange-l
or email: MIDRANGE-L-request@xxxxxxxxxxxx
Before posting, please take a moment to review the archives
at http://archive.midrange.com/midrange-l.




As an Amazon Associate we earn from qualifying purchases.

This thread ...

Replies:

Follow On AppleNews
Return to Archive home page | Return to MIDRANGE.COM home page

This mailing list archive is Copyright 1997-2024 by midrange.com and David Gibbs as a compilation work. Use of the archive is restricted to research of a business or technical nature. Any other uses are prohibited. Full details are available on our policy page. If you have questions about this, please contact [javascript protected email address].

Operating expenses for this site are earned using the Amazon Associate program and Google Adsense.