× The internal search function is temporarily non-functional. The current search engine is no longer viable and we are researching alternatives.
As a stop gap measure, we are using Google's custom search engine service.
If you know of an easy to use, open source, search engine ... please contact support@midrange.com.



Al,

I think you read Dave's response wrong.  When he said "if it appears under 
QINTER it's the address", he meant the problem is the address is set 
wrong.
I think David's suggestion was right on.

You do have a point that if they are running QCTLSBSD under QBASE their 
results may differ.  Most of our genre using more than five 5250 sessions 
are.  However a strictly Domino, or WAS, shop might not.  (We're split 
about 50/50.)

Rob Berendt
-- 
Group Dekko Services, LLC
Dept 01.073
PO Box 2000
Dock 108
6928N 400E
Kendallville, IN 46755
http://www.dekko.com





Al Barsa <barsa@xxxxxxxxxxxxxxxxxxx> 
Sent by: midrange-l-bounces@xxxxxxxxxxxx
04/01/2005 10:06 AM
Please respond to
Midrange Systems Technical Discussion <midrange-l@xxxxxxxxxxxx>


To
Midrange Systems Technical Discussion <midrange-l@xxxxxxxxxxxx>
cc

Subject
Re: IPL Error







Dave,

I would respectfully disagree.  The console should show up in the
controlling subsystem.  IBM ships two controlling subsystems, QBASE and
QCTL, however you can change this to any subsystem you want.  This is
determined by the system value QCTLSBSD.

Al

Al Barsa, Jr.
Barsa Consulting Group, LLC

400>390

"i" comes before "p", "x" and "z"
e gads

Our system's had more names than Elizabeth Taylor!

914-251-1234
914-251-9406 fax

http://www.barsaconsulting.com
http://www.taatool.com
http://www.as400connection.com



 
             daparnin@cooperst 
             andard.com 
             Sent by:                                                   To 

             midrange-l-bounce         midrange-l@xxxxxxxxxxxx 
             s@xxxxxxxxxxxx                                             cc 

 
                                                                   Subject 

             04/01/2005 09:24          Re: IPL Error 
             AM 
 
 
             Please respond to 
             Midrange Systems 
                 Technical 
                Discussion 
             <midrange-l@midra 
                 nge.com> 
 
 








We found that we had a similar situation except that we found it on the
first IPL of a V5R3 upgrade.  Our original twinax console had died last
year and was replaced with another twinax terminal but was never set to
address 0.  A normal IPL found it plugged into port 0 but this one did 
not.
If you do a normal IPL does the console show up under QINTER or QCTL?  If
QINTER I would say that it's the address.


Dave Parnin
Nishikawa Standard Company
Topeka, IN  46571
daparnin@xxxxxxxxxxxxxxxxxx






                      Keith Carpenter

                      <carpcon@xxxxxxx>           To:       Midrange
Systems Technical Discussion
                      Sent by:
<midrange-l@xxxxxxxxxxxx>@SMTP@CTB
                      midrange-l-bounces@m        cc:       (bcc: David A
Parnin/Topeka/NISCO/SPCO)
                      idrange.com                 Subject:  Re: IPL Error



                      03/31/2005 11:03 PM

                      Please respond to

                      Midrange Systems

                      Technical Discussion

                      <midrange-l@midrange

                      .com>






For a twinax terminal to be a "console" it must be set to address 0 and
be on port 0 of the first twinax controller.  Anything else will *only*
work when the OS is running (after IPL).



dpalme@xxxxxxxxxxx wrote:
> I was working from the console, our console is connected via twinax and
with
> a normal IPL it loads fine, and we can log in from the console with no
> problem, perform normal everyday routines, it is only when attempting a
BM
> that it fails.
>
> The console is connected and powered on
>
>
--
This is the Midrange Systems Technical Discussion (MIDRANGE-L) mailing 
list
To post a message email: MIDRANGE-L@xxxxxxxxxxxx
To subscribe, unsubscribe, or change list options,
visit: http://lists.midrange.com/mailman/listinfo/midrange-l
or email: MIDRANGE-L-request@xxxxxxxxxxxx
Before posting, please take a moment to review the archives
at http://archive.midrange.com/midrange-l.


--
This is the Midrange Systems Technical Discussion (MIDRANGE-L) mailing 
list
To post a message email: MIDRANGE-L@xxxxxxxxxxxx
To subscribe, unsubscribe, or change list options,
visit: http://lists.midrange.com/mailman/listinfo/midrange-l
or email: MIDRANGE-L-request@xxxxxxxxxxxx
Before posting, please take a moment to review the archives
at http://archive.midrange.com/midrange-l.



-- 
This is the Midrange Systems Technical Discussion (MIDRANGE-L) mailing 
list
To post a message email: MIDRANGE-L@xxxxxxxxxxxx
To subscribe, unsubscribe, or change list options,
visit: http://lists.midrange.com/mailman/listinfo/midrange-l
or email: MIDRANGE-L-request@xxxxxxxxxxxx
Before posting, please take a moment to review the archives
at http://archive.midrange.com/midrange-l.



As an Amazon Associate we earn from qualifying purchases.

This thread ...

Replies:

Follow On AppleNews
Return to Archive home page | Return to MIDRANGE.COM home page

This mailing list archive is Copyright 1997-2024 by midrange.com and David Gibbs as a compilation work. Use of the archive is restricted to research of a business or technical nature. Any other uses are prohibited. Full details are available on our policy page. If you have questions about this, please contact [javascript protected email address].

Operating expenses for this site are earned using the Amazon Associate program and Google Adsense.