RE: CA/400 Prestart job ending by itself (QNPSERVR)

[Scott Mildenberger <Smildenber@xxxxxxxxxxxx>]

You might want to look at the max storage allowed for user profile quser.
We haven't seen this exact problem but have seen similar caused by quser
reaching it's max storage limit.  If the storage used is near the max try
bumping the max up a bit to see if that helps.

> -----Original Message-----
> From: Roger Vicker, CCP [SMTP:rvicker@vicker.com]
> Sent: Friday, January 28, 2000 3:11 PM
> To:   Midrange List
> Subject:      CA/400 Prestart job ending by itself (QNPSERVR)
> 
> Hi, 
> 
> I've got a customer with a model 620 running V4R2M0 that is being accessed
> by twinax PCs using CA/400 V3R2M0 (current SP) but the network print job
> in QCMN (QNPSERVR) keeps ending. I found a note on IBM that a few PTFs
> were required and applied them. Otherwise I haven't been able to find
> anything (RTFM or Midrange-L archives) that explains this. I can STRPJ
> QCMN QIWS/QNPSERVR and everyone can use the AS/400 as a print server for a
> while but eventually the the job(s) end. After that any PC that tries to
> access the AS/400 network printer generates a QSYSOPER message: 
> 
> Message ID . . . . . . :   CPF1269       Severity . . . . . . . :   00 
> Message type . . . . . :   Information 
> Date sent  . . . . . . :   01/24/00      Time sent  . . . . . . :
> 15:16:04 
> 
> Message . . . . :   Program start request received on communications
> device 
>   FWDPC316 was rejected with reason codes 804, 0. 
> Cause . . . . . :   The program start request was rejected in job 
>   126979/QSYS/QCMN. The device belongs to remote location FWDPC316. If the
> 
>   device is an advanced program-to-program communications (APPC) device,
> the 
>   program start request was received on mode QPCSUPP with unit-of-work 
>   identifier APPN.S102M5DM-404040404040-0001. The first reason code means:
> 
>   Prestart job is inactive or is ending. The second reason code means:
> None. 
> Recovery  . . . :   See the job log for more information about the
> problem. 
> 
> The joblog for QCMN shows a message of : 
> 
> Message ID . . . . . . :   CPF1283       Severity . . . . . . . :   60 
> Message type . . . . . :   Completion 
> Date sent  . . . . . . :   01/28/00      Time sent  . . . . . . :
> 15:02:49 
>   
> Message . . . . :   Subsystem QCMN cannot start prestart job QNPSERVR. 
> Cause . . . . . :   Prestart job 146091/QUSER/QNPSERVR that uses program 
>   QNPSERVR in library QIWS cannot be started because an error in the
> program 
>   occurred before the device was acquired. 
> Recovery  . . . :   Display the job log for the job for more information.
> Wait 
>   until message CPC0905 appears on the QSYSOPR message queue, indicating
> that 
>   the entry is no longer active. To start new jobs, enter the Start
> Prestart 
>   Jobs (STRPJ) command. 
> 
> Before (sometimes after) that there is usually but not always a message: 
> 
> Message ID . . . . . . :   CPF0920       Severity . . . . . . . :   60 
> Message type . . . . . :   Completion 
> Date sent  . . . . . . :   01/28/00      Time sent  . . . . . . :
> 14:45:05 
>   
> Message . . . . :   All prestart jobs are ending for program QNPSERVR in
> QIWS. 
> Cause . . . . . :   All prestart jobs for program QNPSERVR in library QIWS
> in 
>   subsystem QCMN are ending for reason 2.  See reason 2 shown below: 
>     1 - The End Prestart Job (ENDPJ) command was entered. 
>     2 - An error occurred when new jobs were being started. 
>     For reason 2, display the job log (DSPJOBLOG command) for the
> subsystem to 
>   determine the cause of the error. 
>     When all the prestart jobs have ended, message CPC0905 will appear in
> the 
>   subsystem job log and the system operator message queue. 
> Recovery  . . . :   To start jobs, display the system operator (QSYSOPR) 
>   message queue (DSPMSG command). After message CPC0905 appears in the
> message 
>   queue, enter the Start Prestart Jobs (STRPJ) command. 
> 
> Any advice before I go to Support Line? Since the system is 400 miles away
> from the PCs the co-ordination can be complicated. 
> 
> TIA 
> 
> Roger Vicker, CCP 
> 
> -- 
> *** Vicker Programming and Service *** Have bits will byte ***
> www.vicker.com *** 
> If it ain't broke, always try to fix it anyway. 
>  
+---
| This is the Midrange System Mailing List!
| To submit a new message, send your mail to MIDRANGE-L@midrange.com.
| To subscribe to this list send email to MIDRANGE-L-SUB@midrange.com.
| To unsubscribe from this list send email to MIDRANGE-L-UNSUB@midrange.com.
| Questions should be directed to the list owner/operator: david@midrange.com
+---