Oh, I've haven't used STRRSESVR for years, so I cannot help you with
that. Personnaly, I've never needed it, so perhaps I don't understand
what it's good for. My recollection is that SEP totally negated the
need for STRRSESVR when using the debug client.
Connecting remotely could easily cause this problem, depending on how
that remote connection is supported. We use a SSL proxy to tunnel into
our network, and the proxy itself acts as a firewall, requiring all
ports to an address to be defined. We had to scour the documentation to
figure out all the ports...
In this case, SEP debugger normally runs on port 3825, I think. Check
with your network admin.
Hth,
-Eric DeLong
-----Original Message-----
From: wdsci-l-bounces@xxxxxxxxxxxx [mailto:wdsci-l-bounces@xxxxxxxxxxxx]
On Behalf Of Carl R. Hemperly
Sent: Wednesday, July 28, 2010 1:33 PM
To: Rational Developer for IBM i / Websphere Development Studio
ClientforSystem i & iSeries
Subject: Re: [WDSCI-L] No SEP' s ever show up in the list.
All of that looks fine, There are no error messages and everything is
running in the correct place.
Since the STRRSESVR was giving me an error, it looks like the iSeries
cannot find my PC's IP address.
I am connected remotely so most likely that is part or all of the issue.
Either firewall or some translation is probably going on.
Will pursue it through the network group. Thanks for all the
suggestions. Got me to think and look in more detail.
Randy
-----Original Message-----
From: wdsci-l-bounces@xxxxxxxxxxxx [mailto:wdsci-l-bounces@xxxxxxxxxxxx]
On Behalf Of DeLong, Eric
Sent: Wednesday, July 28, 2010 11:20 AM
To: Rational Developer for IBM i / Websphere Development Studio
ClientforSystem i & iSeries
Subject: Re: [WDSCI-L] No SEP' s ever show up in the list.
Callback port 4300 is not really used anymore, I think. You really need
to follow the instructions on the IBM support document to ensure that
your QUSRNOMAX jobQ is attached to the correct subsystem.
-Eric DeLong
-----Original Message-----
From: wdsci-l-bounces@xxxxxxxxxxxx [mailto:wdsci-l-bounces@xxxxxxxxxxxx]
On Behalf Of Carl R. Hemperly
Sent: Wednesday, July 28, 2010 9:13 AM
To: Rational Developer for IBM i / Websphere Development Studio
ClientforSystem i & iSeries
Subject: Re: [WDSCI-L] No SEP' s ever show up in the list.
That's interesting, QB5ROUTER is running in QUSRWRK and QB5ROUTE is
running in QSYSWRK. This is also true when I start it from WDSC. I just
verified the connection and while the PTF's for the debugger look OK I
see there is a problem with host callbacks. The callback to my PC on
port 4300 failed.
-----Original Message-----
From: wdsci-l-bounces@xxxxxxxxxxxx [mailto:wdsci-l-bounces@xxxxxxxxxxxx]
On Behalf Of DeLong, Eric
Sent: Tuesday, July 27, 2010 4:50 PM
To: Rational Developer for IBM i / Websphere Development Studio
ClientforSystem i & iSeries
Subject: Re: [WDSCI-L] No SEP' s ever show up in the list.
What subsystem are those jobs running in. As I recall, there was a time
when these jobs would get started in the wrong subsystem.
http://www-01.ibm.com/support/docview.wss?uid=nas1fd80cef69422ec0c862571
090076ff50
hth,
-Eric
-----Original Message-----
From: wdsci-l-bounces@xxxxxxxxxxxx [mailto:wdsci-l-bounces@xxxxxxxxxxxx]
On Behalf Of Carl R. Hemperly
Sent: Tuesday, July 27, 2010 2:55 PM
To: wdsci-l@xxxxxxxxxxxx
Subject: [WDSCI-L] No SEP' s ever show up in the list.
Using WDSC 7.0.0.8, on this iSeries, I have never gotten an SEP to
appear on the list. I get an error message if the debug server is not
started. I can start the server which starts two jobs:
QB5ROUTER USRPRFXXX BATCH ACTIVE PGM-QB5ROUTER
QSYSJOBD USRPRFXXX BATCH ACTIVE PGM-Q5BROUTE
When I attempt to set a SEP, either in table view or from the library
list, there is no error, nothing happens at all. I have used this in the
past on a different system with no problems.
From searching the archives, there are questions about this job :
QB5PHSRV - which is not running on this system. Could that be the
problem?
Thanks for any help, I miss using this debugger!
Randy Hemperly
Global Data Consultants, LLC
1144 Kennebec Drive
Chambersburg, PA 17201
717-262-2080-X 356
http://www.globaldataconsultants.com
************************************************************************
**************
NOTICE: This e-mail transmission, including any attachments, is
intended solely for the use of the individual(s) or organization(s) to
which it is addressed. If you are not a designated recipient, you are
prohibited from reviewing, using, copying or distributing this message
unless you receive express permission, in writing, from Global Data
Consultants, LLC or the designated recipient. If you received this
e-mail in error, please notify the sender by reply e-mail or by
contacting Global Data Consultants, LLC at (717) 262-2080. If you are
not the designated recipient, you are required to delete this e-mail
from your system without copying it.
midrange.com
