Commands can be set to only run in certain settings, Interactively, In a
batch job etc.
Perhaps during your V5R4 upgrade, the CRTCLPGM has been installed or
modified with reduced capabilities. Following is the output of DSPCMD CMD
(CRTCLPGM) on our V5R4 system. Check if your command is set up with the
required values for the Modes and Where allowed to run options.
Display Command Information
Command . . . . . . . : CRTCLPGM Library . . . . . . . : QSYS
Program to process command . . . . . . : QCLENTR
Library . . . . . . . . . . . . . . : QSYS
State used to call program . . . . . : *SYSTEM
Source file . . . . . . . . . . . . . : S000038666
Library . . . . . . . . . . . . . . : QTEMP
Source file member . . . . . . . . . . : CRTCLPGM
Validity checking program . . . . . . : *NONE
Mode(s) in which valid . . . . . . . . : *PROD
*DEBUG
*SERVICE
Where allowed to run . . . . . . . . . : *IMOD *BMOD *IREXX
*BREXX *BPGM *IPGM
*EXEC *INTERACT *BATCH
Allow limited user . . . . . . . . . . : *NO
Maximum positional parameters . . . . : 5
regards
JAMES O'SULLIVAN
Senior Technical Consultant
CSC
Royal Pavilion, Wellesley Road, Aldershot, Hampshire, GU11 1PZ, UK.
Financial Services EMEA | p:+44 1252 536681 | f:+44 1252 534022 | m:+44
7827 843323 | josulli4@xxxxxxx | www.csc.com/uk
CSC â This is a PRIVATE message. If you are not the intended recipient,
please delete without copying and kindly advise us by e-mail of the mistake
in delivery. NOTE: Regardless of content, this e-mail shall not operate to
bind CSC to any order or other contract unless pursuant to explicit written
agreement or government initiative expressly permitting the use of e-mail
for such purpose â CSC Computer Sciences Limited â Registered Office: Royal
Pavilion, Wellesley Road, Aldershot, Hampshire, GU11 1PZ, UK â Registered
in England No: 0963578
Jeff Buening
<JeffBuening@celi
nainsurance.com> To
Sent by: wdsci-l@xxxxxxxxxxxx
wdsci-l-bounces@m cc
idrange.com
Subject
[WDSCI-L] CL CRTCLPGM ISSUE WDSC
11/05/2009 20:49
Please respond to
Websphere
Development
Studio Client for
iSeries
<wdsci-l@midrange
.com>
Since moving to V5R4 on our ISeries been getting the following error when
trying to Compile a CL in WDSC. Not doing anything different than before
just right clicking on the program and selecting Compile. Everyone else
in office has same issue also. I am on WDSC 7.0.0.6 another person is on
7.0.0.4 same issue for both. Any one else have this issue?????
CRTCLPGM PGM(BUENJE1/PRDXCONCAL) SRCFILE(BUENJE1/QCLSRC)
SRCMBR(PRDXCONCAL) OPTION(*SRCDBG) REPLACE(*YES)
Command CRTCLPGM not allowed in this setting.
Cause . . . . . : The complete list of settings includes: batch,
interactive, batch control language (CL) program, interactive CL program,
batch REXX procedure, interactive REXX procedure, batch CL ILE program,
interactive CL ILE program, CALL to QCMDEXC, and various types of source
statements. The Display Command (DSPCMD) command can be used to determine
the setting in which the command is allowed. Recovery . . . : Omit the
command.
Error found on CRTCLPGM command.
Cause . . . . . : The system detected errors in the command. Recovery .
. . : See the previously listed messages in the job log. Correct the
errors and then try the command again. *N instead of a command name means
that the name had not been determined before the error was found.
Thanks,
Jeff
--
This is the Websphere Development Studio Client for iSeries (WDSCI-L)
mailing list
To post a message email: WDSCI-L@xxxxxxxxxxxx
To subscribe, unsubscribe, or change list options,
visit:
http://lists.midrange.com/mailman/listinfo/wdsci-l
or email: WDSCI-L-request@xxxxxxxxxxxx
Before posting, please take a moment to review the archives
at
http://archive.midrange.com/wdsci-l..
midrange.com
