Re: strdbgsvr

[Jerry Adams <jerry@xxxxxxxxxxxxxxx>]

We're on V5R4 now, but just came off of V5R3 a couple of weeks ago.  The 
QUSRWRK subsystem was always active and never impacted performance.  
Right now there are several pre-start jobs running in it, plus 70+ 
SRVMONxx batch jobs. 


I don't see that starting a subsystem alone would eat up resources 
causing a performance issue.  There must have been something running 
within the subsystem that caused the problem.  For example, the QBATCH 
subsystem is probably always running on our systems, but, if a runaway 
job submitted to batch started chewing up cycles, I wouldn't look to the 
subsystem per se as the culprit, but to the job running within the 
subsystem.


        * Jerry C. Adams
*IBM System i5/iSeries Programmer/Analyst
B&W Wholesale Distributors, Inc.* *
voice
        615.995.7024
fax
        615.995.1201
email
        jerry@xxxxxxxxxxxxxxx <mailto:jerry@xxxxxxxxxxxxxxx>



Brad Abernathy wrote:
> Hi,
>
> Yes, that solution does work, but our systems manager recalls a
> performance issue with using QUSRWRK from V5R1. Of course, we are no
> longer on V5R1, we are on V5R3. 
>
> I suppose the real question would be is anyone having an issue with
> QUSRWRK and V5R3?
>
> Thanks!!
>
> bca
>
> -----Original Message-----
> From: wdsci-l-bounces@xxxxxxxxxxxx [mailto:wdsci-l-bounces@xxxxxxxxxxxx]
> On Behalf Of Xuan Chen
> Sent: Wednesday, June 06, 2007 2:24 PM
> To: Websphere Development Studio Client for iSeries
> Cc: Li Ding
> Subject: Re: [WDSCI-L] strdbgsvr
>
> Could you please try to hook up your QUSRNOMAX to QSYSWRK?  Then the
> debug 
> router and the debug server job (each debug session has a corresponding 
> debug server job) will be run in QSYSWRK subsystem.
>
>
> Thanks,
>
> Xuan Chen,  Problem Determination Tools for iSeries
> (905) 413-3769 T/L 969-3769
> xuanchen@xxxxxxxxxx
>
>
>
>
>
> jstevens@xxxxxxxxxxxxxx 
> Sent by: wdsci-l-bounces@xxxxxxxxxxxx
> 06/06/2007 02:11 PM
> Please respond to
> Websphere Development Studio Client for iSeries <wdsci-l@xxxxxxxxxxxx>
>
>
> To
> Websphere Development Studio Client for iSeries <wdsci-l@xxxxxxxxxxxx>
> cc
>
> Subject
> Re: [WDSCI-L] strdbgsvr
>
>
>
>
>
>
> I have to start it with ALLOBJAUT, otherwise it won't work for me.
>
>
> Jeff Stevens
> Mize, Houser & Co. P.A.
> 913 451 1882
> JStevens@xxxxxxxxxxxxxx
>
>
>
>
>
> "Brad Abernathy" <babernathy@xxxxxxxxxxxxxxxxxx> 
> Sent by: wdsci-l-bounces@xxxxxxxxxxxx
> 06/06/2007 01:09 PM
> Please respond to
> Websphere Development Studio Client for iSeries <wdsci-l@xxxxxxxxxxxx>
>
>
> To
> <WDSCI-L@xxxxxxxxxxxx>
> cc
>
> Subject
> [WDSCI-L] strdbgsvr
>
>
>
>
>
>
> Hi,
>
>  
>
> I cannot get the STRDBGSVR command to complete normally. It puts a job
> in QUSRNOMAX, but it goes nowhere. I did some research and saw a lot of
> people saying that QUSRWRK had to be running. So on our test box, I
> started that subsystem and tried it again. It worked!! However the
> systems manager has some concerns about starting QURSWRK on the
> production box as he had some issue with it taking too much resources on
> V5R1. 
>
>  
>
> We are now on V5R3, but I don't know if there would be an issue with
> this or not.
>
>  
>
> Anyone have any advice on this?
>
>  
>
> Thanks in advance!
>
>  
>
> Brad Abernathy
>
> Sunbelt Rentals
>
>  
>
>