Re: **SPAM** Re: If - Endif

["Kyle Collie" <kcollie@xxxxxxxxx>]

Yea, this bugged me too until I learned to ALT+S on those lines.

Kyle

On 11/16/06, Holden Tommy <Tommy.Holden@xxxxxxxxxxxxxxxxx> wrote:
> <snip>
> But I think you mean that you did the IF and it added an ENDIF, then you
> went back to the IF line and pressed enter again, right? And it added
> another ENDIF, right?
> </snip>
> That's the main reason I disabled that function...it's more annoying to
> me than helpful, especially when modifying existing code.
>
> I think I can still type endif when I need it ;-)
>
> Thanks,
> Tommy Holden
>
>
> -----Original Message-----
> From: wdsci-l-bounces@xxxxxxxxxxxx [mailto:wdsci-l-bounces@xxxxxxxxxxxx]
> On Behalf Of Michael Ryan
> Sent: Thursday, November 16, 2006 9:22 AM
> To: Websphere Development Studio Client for iSeries
> Subject: **SPAM** Re: [WDSCI-L] If - Endif
>
> I added a line with the IF, it dropped me to the next (new, blank) line
> and
> added an ENDIF after that. I entered a like on the new, blank line. I
> pressed enter, it didn't add another ENDIF.
>
> But I think you mean that you did the IF and it added an ENDIF, then you
> went back to the IF line and pressed enter again, right? And it added
> another ENDIF, right?
>
> Try going to the start of the new line and pressing enter. That should
> open
> a new, blank line.
>
> On 11/16/06, Turnidge, Dave <DTurnidge@xxxxxxxxxxxxxxxxxxxx> wrote:
> >
> > "added a line after the IF"
> >
> > Go to the end of the IF line and press enter. I get another endif.
> >
> > OR, did you "add another line" using some action other than the enter
> > key at the end of the IF line?
> >
> > -----Original Message-----
> > From: wdsci-l-bounces@xxxxxxxxxxxx
> [mailto:wdsci-l-bounces@xxxxxxxxxxxx]
> > On Behalf Of Michael Ryan
> > Sent: Thursday, November 16, 2006 9:04 AM
> > To: Websphere Development Studio Client for iSeries
> > Subject: Re: [WDSCI-L] If - Endif
> >
> > Hmm...I don't use the automatic closure of a control block (I find it
> > annoying), but I believe it only adds an ENDIF if an IF is entered. I
> > just turned it on, did an IF, pressed enter and it put in an ENDIF. I
> > did another IF (same behavior), added a line after the IF and it
> didn't
> > add another ENDIF.
> >
> > On 11/16/06, Bill Barnes <bbarnes@xxxxxxxxxxxxx> wrote:
> > >
> > > This is just a suggestion.  It is very nice to have the editor add
> the
> >
> > > ENDIF when you create an IF.  It is annoying when you need to insert
> a
> >
> > > line after the IF and it creates another ENDIF.  I assume that the
> > > same would happen with a DOW/DOU/FOR and SELECT.
> > >
> > >
> > >
> > > Thanks
> > >
> > > Bill Barnes
> > >
> > > The Pantry, Inc
> > >
> > > --
> > > This is the Websphere Development Studio Client for iSeries
> (WDSCI-L)
> >
> > > mailing list To post a message email: WDSCI-L@xxxxxxxxxxxx To
> > > subscribe, unsubscribe, or change list options,
> > > visit: http://lists.midrange.com/mailman/listinfo/wdsci-l
> > > or email: WDSCI-L-request@xxxxxxxxxxxx Before posting, please take a
> > > moment to review the archives at
> http://archive.midrange.com/wdsci-l.
> > >
> > --
> > This is the Websphere Development Studio Client for iSeries  (WDSCI-L)
> > mailing list To post a message email: WDSCI-L@xxxxxxxxxxxx To
> subscribe,
> > unsubscribe, or change list options,
> > visit: http://lists.midrange.com/mailman/listinfo/wdsci-l
> > or email: WDSCI-L-request@xxxxxxxxxxxx
> > Before posting, please take a moment to review the archives at
> > http://archive.midrange.com/wdsci-l.
> >
> > --
> > This is the Websphere Development Studio Client for iSeries  (WDSCI-L)
> > mailing list
> > To post a message email: WDSCI-L@xxxxxxxxxxxx
> > To subscribe, unsubscribe, or change list options,
> > visit: http://lists.midrange.com/mailman/listinfo/wdsci-l
> > or email: WDSCI-L-request@xxxxxxxxxxxx
> > Before posting, please take a moment to review the archives
> > at http://archive.midrange.com/wdsci-l.
> >
> --
> This is the Websphere Development Studio Client for iSeries  (WDSCI-L)
> mailing list
> To post a message email: WDSCI-L@xxxxxxxxxxxx
> To subscribe, unsubscribe, or change list options,
> visit: http://lists.midrange.com/mailman/listinfo/wdsci-l
> or email: WDSCI-L-request@xxxxxxxxxxxx
> Before posting, please take a moment to review the archives
> at http://archive.midrange.com/wdsci-l.
>
> --
> This is the Websphere Development Studio Client for iSeries  (WDSCI-L) mailing 
> list
> To post a message email: WDSCI-L@xxxxxxxxxxxx
> To subscribe, unsubscribe, or change list options,
> visit: http://lists.midrange.com/mailman/listinfo/wdsci-l
> or email: WDSCI-L-request@xxxxxxxxxxxx
> Before posting, please take a moment to review the archives
> at http://archive.midrange.com/wdsci-l.