Re: Preferences - LPEX Editor

Rick,

Thanks.

        * Jerry C. Adams
*iSeries/i5 Programmer/Analyst
B&W Wholesale Distributors, Inc.* *
voice
        615.893.8633x152
fax
        615.995.1201
email
        jerry@xxxxxxxxxxxxxxx <mailto:jerry@xxxxxxxxxxxxxxx>



Weber, Richard wrote:

Jerry,

This isn't going to help you much, but, I just installed V6 on Thursday and
I am not having the issues you are having.  After I installed I went and set
the same preferences that you did.  Those being: to repeat the same spec and

the automatic "Endxx" feature and they work fine.

As for the new line not splitting the text like a word editor, the user key
action you are looking for is "splitLine".  Notice the capitalization of the
"L" in line and the lack thereof in the "s".  The functions are case
sensitive.  I have noticed that it doesn't always work when I hit enter even
though I have it set up, I don't know why.

Are there any other preferences you are setting that you didn't mention that
might be causing the conflict?  If so I can compare them to my own.

Rick Weber | TЯU International

-----Original Message-----

From: Jerry Adams [mailto:jerry@xxxxxxxxxxxxxxx] Sent: Monday, October 31, 2005 8:30 AM

To: WDSc Midrange
Subject: Re: [WDSCI-L] Preferences - LPEX Editor

Well, even though I didn't hold out much hope, I uninstalled both WDSc 6.0 and 5.1.2, then installed 6.0 from scratch and installed the updates. Re-define my preferences which should handle these issues.

Didn't work. All of the issues, which I stated below, still exist. Since one respondent said that these work fine for him, I can again only surmise that there is some preference, somewhere that conflicts with or overrides these. If so, it isn't obvious (to moi, anyway) as I went through every single preference section and every panel within each section.

As far as the "Enter" key issue goes, there is a workaround (Ctl+Enter). The action 'newLine' may not be the proper action, but it was the only one that I could find that made sense, and it was the option I used in 5.1.2. But the change I made to the "backSpace" key ('left') works fine in 6.0.

I don't expect any responses as everyone has already had a look at this, if they wanted to. But if anyone should have an epiphany, give me a buzz.

Thanks.


        * Jerry C. Adams
*iSeries/i5 Programmer/Analyst
B&W Wholesale Distributors, Inc.* *
voice
        615.893.8633x152
fax
        615.995.1201
email
        jerry@xxxxxxxxxxxxxxx <mailto:jerry@xxxxxxxxxxxxxxx>



Jerry Adams wrote:

Well, just spent three hours downloading and installing the update. These issues (below) remain. I checked the preferences, as indicated below. In fact, I went through every preference panel, but could not find anything directly relevant that I did not indicate below. My only thoughts are that:

 1. There is a preference setting that is indirectly affecting my
    results, or
 2. The fact that I have both 6.0 and 5.1.2 running on the same PC
    might be causing a clash.

Reasonably (to me, anyway) I doubt #2 is the problem because 5.1.2
works as advertised.

I've had others tell me that these are not issues with them, too.  So

obviously it's a personal issue. I just don't know how personal. If not one else has any suggestions, I may just bite the bullet tomorrow: uninstall both versions and install 6.0 alone.

Thanks.


   * Jerry C. Adams
*iSeries/i5 Programmer/Analyst
B&W Wholesale Distributors, Inc.* *
voice
   615.893.8633x152
fax
   615.995.1201
email
   jerry@xxxxxxxxxxxxxxx <mailto:jerry@xxxxxxxxxxxxxxx>



ssc1478@xxxxxxx wrote:

There are a few of irritants that I have with the LPEX editor under

WDSc 6.0.0. Build 20050609_2105 as opposed to 5.1.2.

After getting the updates, I have Version: 6.0.1 Build id:
20050725_1800.

First, in fixed format RPG, when I press the /Enter/ key, it does

*not* repeat the specification type (F,C, etc.). And I do >have the

preferences set (RemoteSystems...iSeries...LPEX Editor Parsers...ILE RPG: Repeat previous specification type = >checked).

This works for me.

Second, when typing a structured opcode (IF, SELECT, etc.), it does

not automatically apply the closing ENDxx, which 5.1.2 >did. And,

again, the preference is set (same page as above: Automatic closure of control block = checked, Style = ENDXX).

This works for me.

Third, when I press the /Enter/ key, while the cursor is not at the

end of the line, it breaks the line at the point of the >cursor -

which is what one would expect in Word or a text editor. However, 5.1.2 simply created a new line regardless of >where the cursor was in the line. I even added a preference (LPEX Editor...UserKeyActions: enter = newLine). There is a >"workaround" for this one, though: Hold the /Control/ key while pressing /Enter/. I have another action which says:

backSpace = left. Works fine.

This works for me also.  To break the line, I have to press alt-s.
(I wish it wouldn't put the text starting at column 1.)

I use WDSc for editing RPG IV syntax primarily, not web development

(yet). I do have both 6.0 and 5.1.2 installed on the >same PC, but
5.1.2 works as described above, which is the way I want it to work.

Any suggestions, corrections would be appreciated.

I don't know if the updates fixed what you're experiencing because I

don't recall having those problems before I got the updates. (I don't use the automatic closure feature so I can't comment on that.)

hth,
Phil

Thanks.

-- * Jerry C. Adams

*iSeries/i5 Programmer/Analyst
B&W Wholesale Distributors, Inc.* *
voice
615.893.8633x152
fax
615.995.1201
email
jerry@xxxxxxxxxxxxxxx <mailto:jerry@xxxxxxxxxxxxxxx>

-- This is the Websphere Development Studio Client for iSeries
(WDSCI-L) mailing list
To post a message email: WDSCI-L@xxxxxxxxxxxx
To subscribe, unsubscribe, or change list options,
visit: http://lists.midrange.com/mailman/listinfo/wdsci-l
or email: WDSCI-L-request@xxxxxxxxxxxx
Before posting, please take a moment to review the archives
at http://archive.midrange.com/wdsci-l.


_____________________________________________________________________
___

Check Out the new free AIM(R) Mail -- 2 GB of storage and industry-leading spam and email virus protection.