|
Simon,
FFileA O A E K DiskYou're telling me that's not output only?
And the sentence after the quote I provided is:
"The programmer is expected to override the file or use larger blocks
if the default is not appropriate."
But the default _is_ appropriate. It's an output-only specification,
and thus should block (barring other reasons for the file not blocking
which isn't mentioned in the article).
If it's the K you're referring to in the F-Spec as being an issue, I
tried removing it (per an earlier thread response) to no effect.
Hwoever, even with the K it's still output-only. I see no way I could
read or update that file.
Thanks,
-Kurt
-----Original Message-----
From: rpg400-l-bounces@xxxxxxxxxxxx
[mailto:rpg400-l-bounces@xxxxxxxxxxxx]
On Behalf Of Simon Coulter
Sent: Monday, June 07, 2010 6:33 PM
To: RPG programming on the IBM i / System i
Subject: Re: RPG Blocked Writes
On 08/06/2010, at 8:22 AM, Kurt Anderson wrote:
I have a file defined in a program as:https://www-912.ibm.com/s_dir/slkbase.NSF/1ac66549a21402188625680b0002
FFileA O A E K Disk
From my understanding, writes to this file should be blocked.
However when I look at the I/O for the job, the I/O count and the
RRN is always equal. For comparison, reading a file that's blocked
has a lower I/O count than the current RRN.
Is this a matter of me not understanding the I/O screen (when
looking at the job as it is running), or is this file actually
writing a single record at a time?
According to this document, I feel that these writes should be
blocked.
037e/d6738e1cd37e1f33862565c2007cef79?OpenDocument
"All high-level language programs (HLLs) use blocking at certain
times and use single record I/O at other times, based on program
specifications. Because blocking takes less system resources to
perform a single I/O, a program that blocks performs better and uses
less system resources. The default for the HLL uses record blocking
if opening a file for output only (write) or input only (read)."
Read this part again:
"The default for the HLL uses record blocking if opening a file for
output only (write) or input only (read)."
and then compare that with your file specification:
FFileA O A E K Disk
paying particular attention to the use of the word "ONLY" in the
blocking explanation. If that's not clear enough then re-read the
original paragraph (of which you quoted only part)--specifically the
second sentence after the one you think should cause blocking.
Regards,
Simon Coulter.
--------------------------------------------------------------------
FlyByNight Software OS/400, i5/OS Technical Specialists
http://www.flybynight.com.au/
Phone: +61 2 6657 8251 Mobile: +61 0411 091 400 /"\
Fax: +61 2 6657 8251 \ /
X
ASCII Ribbon campaign against HTML E-Mail / \
--------------------------------------------------------------------
--
This is the RPG programming on the IBM i / System i (RPG400-L) mailing
list To post a message email: RPG400-L@xxxxxxxxxxxx To subscribe,
unsubscribe, or change list options,
visit: http://lists.midrange.com/mailman/listinfo/rpg400-l
or email: RPG400-L-request@xxxxxxxxxxxx Before posting, please take a
moment to review the archives at http://archive.midrange.com/rpg400-l.
--
This is the RPG programming on the IBM i / System i (RPG400-L) mailing
list To post a message email: RPG400-L@xxxxxxxxxxxx To subscribe,
unsubscribe, or change list options,
visit: http://lists.midrange.com/mailman/listinfo/rpg400-l
or email: RPG400-L-request@xxxxxxxxxxxx Before posting, please take a
moment to review the archives at http://archive.midrange.com/rpg400-l.
As an Amazon Associate we earn from qualifying purchases.
This mailing list archive is Copyright 1997-2024 by midrange.com and David Gibbs as a compilation work. Use of the archive is restricted to research of a business or technical nature. Any other uses are prohibited. Full details are available on our policy page. If you have questions about this, please contact [javascript protected email address].
Operating expenses for this site are earned using the Amazon Associate program and Google Adsense.