Re: SETGT *End/*Start

Kevin, there are no F specs, just one C spec in the entire source file.
The error is focused on just the one line.
C *START SETGT ITEMBL

This one C spec works fine, doesnt draw the error message.
C *START SETLL ITEMBL


JoeM

----- Original Message -----
From: "Kevin Bucknum" <Kevin@xxxxxxxxxxxxxxxxxxx>
To: "RPG programming on the AS400 / iSeries" <rpg400-l@xxxxxxxxxxxx>
Sent: Wednesday, December 05, 2007 8:59 PM
Subject: RE: SETGT *End/*Start

It is making it's decision based on the K in the file spec.

-----Original Message-----
From: rpg400-l-bounces@xxxxxxxxxxxx

[mailto:rpg400-l-bounces@xxxxxxxxxxxx]

On Behalf Of oplink
Sent: Wednesday, December 05, 2007 8:51 PM
To: RPG programming on the AS400 / iSeries
Subject: Re: SETGT *End/*Start

Mike, the seu message knows nothing about the file at this point, its

the

point of entry when I press enter that the message pops up.



Joe Pluta may be right, its just not acceptable to use *Start/*End

with

SETGT.

I understand its not feasible to list all outcomes that's not

appropriate

but I feel this should have been an exception, I could have lost a
paycheck
on this one!



You can replace with SETLL, or if your not concern with the nulls then

use

*Hival/*Loval along with SETGT.



I just didn't see that one coming. Still, I feel there's something im

not

seeing here.





JoeM


----- Original Message -----
From: "Mike Cunningham" <mcunning@xxxxxxx>
To: "'RPG programming on the AS400 / iSeries'" <rpg400-l@xxxxxxxxxxxx>
Sent: Wednesday, December 05, 2007 6:01 PM
Subject: RE: SETGT *End/*Start

Are you files keyed logicals ?

On SETLL *LOVAL repositions at the start of a keyed file *START
repositions at the start of a non-keyed file
On SETGT *HIVAL repositions at the end of a keyed file *END

repositions

at

the end of a non-keyed file

-----Original Message-----
From: rpg400-l-bounces@xxxxxxxxxxxx [mailto:rpg400-l-

bounces@xxxxxxxxxxxx]

On Behalf Of OPLink
Sent: Wednesday, December 05, 2007 7:16 PM
To: RPG programming on the AS400 / iSeries
Subject: SETGT *End/*Start


We are on 5.3 and I can not use the *END or *START
with SETGT as shown below. In SEU the error message
RNF5318 pops up when enter is pressed. I can not find any
docs on the cause of error or that I can even use the *START/*END
with SETGT. However, they both work fine for SETLL.

Am I missing a PTF??

thanks
JoeM
-----------------------------------

C *START SETGT ITEMBL

Factor 1 entry has a data type that is not allowed for this

operation;

speci...


-----------------------------------
F1 on message line
-----------------------------------
Additional Message Information

Message ID . . . . . . : RNF5318 Severity . . . . . . . :

30

Message type . . . . . : Diagnostic

Message . . . . : Factor 1 entry has a data type that is not

allowed

for

this operation; specification is ignored.
Cause . . . . . : The Factor 1 entry (positions 12 - 25) must have

the

correct data type.
Recovery . . . : Correct the Factor 1 entry (positions 12 - 25).
Compile
again.
--
This is the RPG programming on the AS400 / iSeries (RPG400-L)

mailing

list

To post a message email: RPG400-L@xxxxxxxxxxxx
To subscribe, unsubscribe, or change list options,
visit: http://lists.midrange.com/mailman/listinfo/rpg400-l
or email: RPG400-L-request@xxxxxxxxxxxx
Before posting, please take a moment to review the archives
at http://archive.midrange.com/rpg400-l.


--
This is the RPG programming on the AS400 / iSeries (RPG400-L)

mailing

list

To post a message email: RPG400-L@xxxxxxxxxxxx
To subscribe, unsubscribe, or change list options,
visit: http://lists.midrange.com/mailman/listinfo/rpg400-l
or email: RPG400-L-request@xxxxxxxxxxxx
Before posting, please take a moment to review the archives
at http://archive.midrange.com/rpg400-l.

--
This is the RPG programming on the AS400 / iSeries (RPG400-L) mailing

list

To post a message email: RPG400-L@xxxxxxxxxxxx
To subscribe, unsubscribe, or change list options,
visit: http://lists.midrange.com/mailman/listinfo/rpg400-l
or email: RPG400-L-request@xxxxxxxxxxxx
Before posting, please take a moment to review the archives
at http://archive.midrange.com/rpg400-l.

--
This is the RPG programming on the AS400 / iSeries (RPG400-L) mailing list
To post a message email: RPG400-L@xxxxxxxxxxxx
To subscribe, unsubscribe, or change list options,
visit: http://lists.midrange.com/mailman/listinfo/rpg400-l
or email: RPG400-L-request@xxxxxxxxxxxx
Before posting, please take a moment to review the archives
at http://archive.midrange.com/rpg400-l.