AW: Spool file object

Hi,

With the following steps you can replace SNDNETSPLF in the WRKSPLF through a
command of your choice:
1. The SNDNETSPLF-Command call is located in the QCPFMSGF Message-Id CPX3438
and CPX3439.
2. Create a new message file and add CPX3438 and CPX3439 where the command
you want to execute is specified.
3. Copy the command you want to call in the QSYS library
4. Before calling the WRKSPLF-command Override the QCPFMSG with the newly
created message file. In this way the changed CPX3438 and CPX3439 are used
while all other messages are taken from the original QCPFMSG-file. But be
aware you only can pass the same parameters as used in the SNDNETSPLF
command (for example the qualified spoolfile name)
5. After executing the modified WRKSPLF command delete the override.

Mit freundlichen Grüßen / Best regards

Birgitta Hauser

"Shoot for the moon, even if you miss, you'll land among the stars." (Les
Brown)
"If you think education is expensive, try ignorance." (Derek Bok)
"What is worse than training your staff and losing them? Not training them
and keeping them!"

-----Ursprüngliche Nachricht-----
Von: rpg400-l-bounces@xxxxxxxxxxxx [mailto:rpg400-l-bounces@xxxxxxxxxxxx] Im
Auftrag von Peter Dow (ML)
Gesendet: Tuesday, May 15, 2007 21:26
An: RPG programming on the AS400 / iSeries
Betreff: Re: Spool file object


Not that I know of. I see that WRKSPLF has an option 1 Send, which
invokes SNDNETSPLF. I tried copying SNDTCPSPLF to a library ahead of
QSYS in my library list and naming it as SNDNETSPLF, but option 1 still
goes to SNDNETSPLF, so either it's hardcoded to go to QSYS, or it might
be specified in a message somewhere so that you could change it.

Another option is to get Brad Stone's SPLTOOL, which lets you define
your own options, and provides other options like email, FTP, etc.

Turnidge, Dave wrote:

Interesting that it doesn't show up with F10...?? Never having used
this command, is there any way of accessing it via the WRKSPLF, or
other WRK option?

-----Original Message-----
From: rpg400-l-bounces@xxxxxxxxxxxx
[mailto:rpg400-l-bounces@xxxxxxxxxxxx] On Behalf Of Peter Dow (ML)
Sent: Tuesday, May 15, 2007 1:55 PM
To: RPG programming on the AS400 / iSeries
Subject: Re: Spool file object

Hi Dave,

Prompt with F4, then press F9 to see all possible parameters -- it's
at the bottom of the 2nd page on the v5r3 machine I happen to be on:

Delete file after sending . . . DLTSPLF *NO

*Peter Dow* /
Dow Software Services, Inc.
909 793-9050
pdow@xxxxxxxxxxxxxxx <mailto:pdow@xxxxxxxxxxxxxxx> /

Turnidge, Dave wrote:

I don't see a DLT option - OTOH, I'm looking at 5.3...??

-----Original Message-----
From: rpg400-l-bounces@xxxxxxxxxxxx
[mailto:rpg400-l-bounces@xxxxxxxxxxxx] On Behalf Of Peter Dow (ML)
Sent: Tuesday, May 15, 2007 1:34 PM
To: RPG programming on the AS400 / iSeries
Subject: Re: Spool file object

Try SNDTCPSPLF, it has a DLTSPLF parameter to delete the source spool
file after sending.

*Peter Dow* /
Dow Software Services, Inc.
909 793-9050
pdow@xxxxxxxxxxxxxxx <mailto:pdow@xxxxxxxxxxxxxxx> /

Turnidge, Dave wrote:

Unfortunately...or not...it doesn't "MOVE", but rather copies... Now
if there was a way to MOVE the spool file, that would be an
interesting bit of information...

-----Original Message-----
From: rpg400-l-bounces@xxxxxxxxxxxx
[mailto:rpg400-l-bounces@xxxxxxxxxxxx] On Behalf Of Phil Kestenbaum
Sent: Tuesday, May 15, 2007 11:14 AM
To: RPG programming on the AS400 / iSeries
Subject: RE: Spool file object

Correct. I can use the sndnetsplf
To move them when it happens.

--
This is the RPG programming on the AS400 / iSeries (RPG400-L) mailing
list To post a message email: RPG400-L@xxxxxxxxxxxx To subscribe,
unsubscribe, or change list options,
visit: http://lists.midrange.com/mailman/listinfo/rpg400-l
or email: RPG400-L-request@xxxxxxxxxxxx Before posting, please take a
moment to review the archives at http://archive.midrange.com/rpg400-l.

--
This is the RPG programming on the AS400 / iSeries (RPG400-L) mailing
list To post a message email: RPG400-L@xxxxxxxxxxxx To subscribe,
unsubscribe, or change list options,
visit: http://lists.midrange.com/mailman/listinfo/rpg400-l
or email: RPG400-L-request@xxxxxxxxxxxx
Before posting, please take a moment to review the archives at
http://archive.midrange.com/rpg400-l.