R: QtmmSendMail problem....

["Gurrieri Fabrizio" <fabrizio.gurrieri@xxxxxxxxxxxx>]

Thanks but I solving the problem: the mime file is correct but before I callb 
the api I've to change in its parameters '@' with '§' in the two addresses so 
AS/400 recognize it as user and domain separator.


Fabrizio Gurrieri - BARTOLINI SPA
Via E.Mattei  42 - 40138 BOLOGNA (Italy)
Tel:+39 051 6015593 - Fax:+39 051 530365
E-Mail: Fabrizio.Gurrieri@bartolini.it
Internet: http://www.bartolini.it



-----Messaggio originale-----
Da: Christopher A. Libby [mailto:clibby@mainepublicservice.com]
Inviato: giovedì 27 giugno 2002 15.46
A: rpg400-l@midrange.com
Oggetto: Re: QtmmSendMail problem....


Try removing "<mailto:ced@bartolini.it>" - "mailto:"; is not a valid email
address.  Try using just the email address.

----- Original Message -----
From: "Gurrieri Fabrizio" <fabrizio.gurrieri@bartolini.it>
To: <rpg400-l@midrange.com>
Sent: Thursday, June 27, 2002 5:09 AM
Subject: QtmmSendMail problem....


This is a multi-part message in MIME format.
--
[ Picked text/plain from multipart/alternative ]
Hi,
    today I try to use the API QtmmSendMail to send an e-mail message from
my AS/400 but it doesn't work.
I look that the mime-file are created and after the callb of the api
QtmmSendMail  it is deleted from my IFS but the e-mail doesn't be send.

This is my mimefile:



Sender:  <mailto:ced@bartolini.it> ced@bartolini.it
Date:
From:  <  <mailto:ced@bartolini.it> ced@bartolini.it>
MIME-Version: 1.0
To:  <mailto:fabrizio.gurrieri@bartolini.it> fabrizio.gurrieri@bartolini.it
Subject:
Content-Type: multipart/mixed; boundary="--PART.BOUNDARY.1"

This is a multi-part message in MIME format.

----PART.BOUNDARY.1
Content-Type: text/plain; charset=us-ascii
Content-Transfer-Encoding: 7bit





----PART.BOUNDARY.1--




And the message that I have in job QMSF under QSYSWRK subsystem is:




ID messaggio . . . . . :   TCP5128       Gravità  . . . . . . . :   30
Tipo messaggio . . . . :   Diagnostico
Data invio . . . . . . :   27/06/02      Ora invio  . . . . . . :   10:43:08

Messaggio . . . :   Unable to send non-delivery note.
Cause . . . . . :   The POP non-delivery exit was trying to notify an
  originator of a failure to deliver a note. The non-delivery note was not
  deliverable.

 The originator of the note was:  <mailto:ced@bartolini.it> ced@bartolini.it
Recovery  . . . :   This message is issued when a non-delivery note cannot
be
  sent to the originator of a note. There may be an error in the directory
or
  the SMTP alias table for this address.



If I use SNDDST the e-mail will be send correctly, have I start or configure
any service on the AS/400?
Any ideas???

Thank a lot





Fabrizio Gurrieri - BARTOLINI SPA
Via E.Mattei  42 - 40138 BOLOGNA (Italy)
Tel:+39 051 6015593 - Fax:+39 051 530365
E-Mail: Fabrizio.Gurrieri@bartolini.it
Internet: http://www.bartolini.it <http://www.bartolini.it/>


_______________________________________________
This is the RPG programming on the AS400 / iSeries (RPG400-L) mailing list
To post a message email: RPG400-L@midrange.com
To subscribe, unsubscribe, or change list options,
visit: http://lists.midrange.com/cgi-bin/listinfo/rpg400-l
or email: RPG400-L-request@midrange.com
Before posting, please take a moment to review the archives
at http://archive.midrange.com/rpg400-l.


_______________________________________________
This is the RPG programming on the AS400 / iSeries (RPG400-L) mailing list
To post a message email: RPG400-L@midrange.com
To subscribe, unsubscribe, or change list options,
visit: http://lists.midrange.com/cgi-bin/listinfo/rpg400-l
or email: RPG400-L-request@midrange.com
Before posting, please take a moment to review the archives
at http://archive.midrange.com/rpg400-l.