|
Job . . : QZDASOINIT User . . : QUSER Number . . . :
139403
Job 139403/QUSER/QZDASOINIT started on 03/20/26 at 11:41:56 in
subsystem
QSERVER in QSYS. Job entered system on 03/20/26 at 11:41:56.
Tried to refer to all or part of an object that no longer exists.
Value for call stack counter parameter not valid.
Application error. MCH3402 unmonitored by QZDASRV at statement
0000031317, instruction X'0000'.
This job ended abnormally.
Job 139403/QUSER/QZDASOINIT ended on 03/20/26 at 11:41:56; .003 seconds
used; end code 30 .
And the individual messages:
Message ID . . . . . . : MCH3402 Severity . . . . . . . : 40
Message type . . . . . : Escape
Date sent . . . . . . : 03/20/26 Time sent . . . . . . :
11:41:56
Message . . . . : Tried to refer to all or part of an object that no
longer
exists.
Cause . . . . . : The most common cause is that a stored address to an
object is no longer correct because that object was deleted or part of
the
object was deleted.
Message ID . . . . . . : CPF24A3 Severity . . . . . . . : 40
Message type . . . . . : Escape
Date sent . . . . . . : 03/20/26 Time sent . . . . . . :
11:41:56
Message . . . . : Value for call stack counter parameter not valid.
Cause . . . . . : The value 5, specified for call stack counter
parameter,
is not valid. The value was specified in parameter number 7 on the API.
Recovery . . . : Correct the value for call stack counter parameter and
try
the request again. This value must be greater than or equal to 0 but
cannot
be larger than the number of entries on the call stack.
Message ID . . . . . . : CEE9901 Severity . . . . . . . : 30
Message type . . . . . : Diagnostic
Date sent . . . . . . : 03/20/26 Time sent . . . . . . :
11:41:56
Message . . . . : Application error. MCH3402 unmonitored by QZDASRV at
statement 0000031317, instruction X'0000'.
Cause . . . . . : The application ended abnormally because an exception
occurred and was not handled. The name of the program to which the
unhandled exception is sent is QZDASRV QZDACMDP PRE_START_SETUP. The
program
was stopped at the high-level language statement number(s) 0000031317 at
the
time the message was sent. If more than one statement number is shown,
the
program is an optimized ILE program. Optimization does not allow a
single
statement number to be determined. If *N is shown as a value, it means
the
real value was not available.
Recovery . . . : See the low level messages previously listed to locate
the
cause of the exception. Correct any errors, and then try the request
again.
On Fri, Mar 20, 2026 at 1:31 PM Jim Franz <franz9000@xxxxxxxxx> wrote:
if you are not getting a joblog - check the job description values forto
logging - wrkjobd qdftsvr
Job description . . . . . . . . . . . . . . . . . : QDFTSVR
...
Severity . . . . . . . . . . . . . . . . . . . : 0
Text . . . . . . . . . . . . . . . . . . . . . : *SECLVL
Log CL program commands . . . . . . . . . . . . . : *YES
if not finding the joblogs - could be pending - look at WRKJOB QZDASOINIT
- also make sure user profile quser not disabled
Jim Franz
On Fri, Mar 20, 2026 at 1:04 PM Rob Berendt <robertowenberendt@xxxxxxxxx
wrote:
What is in the QZDASOINIT joblog?
On Fri, Mar 20, 2026 at 12:20 PM Mark Murphy <jmarkmurphy@xxxxxxxxx>
wrote:
I am having trouble with JDBC connectivity. QZDASOINIT will not stay
running. The tech group has replaced an IO card twice in an attempt
ifcorrect the issue, but the same issue remains. I was just wondering
mailinganyusing
of the wizards here have any troubleshooting advice. I can connect
Access Client Solutions, but RDi and SQL clients like DBeaver fail to
connect. I can ping, and JPing from the toolbox works as well.
--
This is the Midrange Systems Technical Discussion (MIDRANGE-L)
relatedlistrelated
To post a message email: MIDRANGE-L@xxxxxxxxxxxxxxxxxx
To subscribe, unsubscribe, or change list options,
visit: https://lists.midrange.com/mailman/listinfo/midrange-l
or email: MIDRANGE-L-request@xxxxxxxxxxxxxxxxxx
Before posting, please take a moment to review the archives
at https://archive.midrange.com/midrange-l.
Please contact support@xxxxxxxxxxxxxxxxxxxx for any subscription
listquestions.--
This is the Midrange Systems Technical Discussion (MIDRANGE-L) mailing
To post a message email: MIDRANGE-L@xxxxxxxxxxxxxxxxxx
To subscribe, unsubscribe, or change list options,
visit: https://lists.midrange.com/mailman/listinfo/midrange-l
or email: MIDRANGE-L-request@xxxxxxxxxxxxxxxxxx
Before posting, please take a moment to review the archives
at https://archive.midrange.com/midrange-l.
Please contact support@xxxxxxxxxxxxxxxxxxxx for any subscription
listquestions.--
This is the Midrange Systems Technical Discussion (MIDRANGE-L) mailing
To post a message email: MIDRANGE-L@xxxxxxxxxxxxxxxxxx--
To subscribe, unsubscribe, or change list options,
visit: https://lists.midrange.com/mailman/listinfo/midrange-l
or email: MIDRANGE-L-request@xxxxxxxxxxxxxxxxxx
Before posting, please take a moment to review the archives
at https://archive.midrange.com/midrange-l.
Please contact support@xxxxxxxxxxxxxxxxxxxx for any subscription related
questions.
This is the Midrange Systems Technical Discussion (MIDRANGE-L) mailing list
To post a message email: MIDRANGE-L@xxxxxxxxxxxxxxxxxx
To subscribe, unsubscribe, or change list options,
visit: https://lists.midrange.com/mailman/listinfo/midrange-l
or email: MIDRANGE-L-request@xxxxxxxxxxxxxxxxxx
Before posting, please take a moment to review the archives
at https://archive.midrange.com/midrange-l.
Please contact support@xxxxxxxxxxxxxxxxxxxx for any subscription related
questions.
As an Amazon Associate we earn from qualifying purchases.
This mailing list archive is Copyright 1997-2026 by midrange.com and David Gibbs as a compilation work. Use of the archive is restricted to research of a business or technical nature. Any other uses are prohibited. Full details are available on our policy page. If you have questions about this, please contact [javascript protected email address].
Operating expenses for this site are earned using the Amazon Associate program and Google Adsense.
midrange.com
