Re: Power 8 Installation Issue

the 57B4 card states:
Removable media device (SAS Tape) are supported in a single controller
configuration only and cannot be combined with disk devices attached to the
same adapter. Removable media is not supported in multi-initiator and high
availability (dual storage IOA) configurations
It also mentions:
Specific AE1 or YE1 SAS cable features are required for SAS Tape attachment

Does your enviroment fulfill those requirements? You might have an
operational card but the LIC can be picky on which configurations it
supports...

Best of luck

On Tue, Jul 14, 2015 at 8:02 PM, Evan Harris <auctionitis@xxxxxxxxx>
wrote:

Yeah, I'm with you on the PTF idea. The IOA comes up fine in service

tools;

it reports as operational.

I haven't found anything so far that suggests the card and tape aren't
supported, other than the reference that said it could not be used for an
ALT-IPL.

Reports as a 57B4 in the HMC, basically a EJ0J which tells me it needs

LIC

of at least TR7 with MF57865, MF57923, MF58006 all of which appear to be

in

TR10 - which is the LIC DVD I am using.

Pre-requisites for EJ0J

https://www-912.ibm.com/e_dir/eserverv7prereq.nsf/HW2/Hardware~eServer~EJ0J~378003673D8750DB86257A910052106D?OpenDocument

Interestingly if I go the System Storage Interoperation Center the

adapter

it tells me I need for the library is a 5912

https://www-304.ibm.com/systems/support/storage/ssic/interoperability.wss

On Wed, Jul 15, 2015 at 10:22 AM, Bryan Dietz <bdietz400@xxxxxxxxx>

wrote:

My first guess is that you are "missing" PTF's that support either the
device or the IOA card.

if you go into service tools to look at the hardware resources what is

the

status?

Bryan


Evan Harris wrote on 7/14/2015 4:48 PM:

Hi guys

I am currently doing a build of a new test system for a customer and
having
a few hiccups along the way.

The machine I am using is a new Power 8 S824 6. It has a TS2900 tape
library with HH LTO6 attached to a 57B4 SAS adapter. It is intended to

run

the IBM i Operating system (no VIOS)

The problems I am having are around getting the tape drive visible. It

is

not supported as an ALT-IPL device as far as I can tell from the IBM

docs.

That's OK, I half expected that and have a V7R1 DVD to boot from

which

according to me is resave level RS-710-N so V7R1 TR10. Despite that I
can't
seem to get the tape library visible as an alternate installation

device

either after booting from DVD.

The library is currently set to sequential mode as an autoloader.

I have an option 21 save from the customer test system and at this

point

what I am thinking about doing is installing LIC form the DVD and then
installing Base OS from DVD as well. After that I will do the rest of

the

recovery from Tape and then go back and reload/re-apply all the PTFs.

Anybody got any other suggestions as to what I missed or what I can

try

?

If the config is not quite supported that's OK, I'd just like to know
that;s the case (haven't been able to track down a definitive IBM doc

as

yet) - I didn't do the config I just got sent out to make it work....

--

This is the Midrange Systems Technical Discussion (MIDRANGE-L) mailing

list

To post a message email: MIDRANGE-L@xxxxxxxxxxxx
To subscribe, unsubscribe, or change list options,
visit: http://lists.midrange.com/mailman/listinfo/midrange-l
or email: MIDRANGE-L-request@xxxxxxxxxxxx
Before posting, please take a moment to review the archives
at http://archive.midrange.com/midrange-l.

--

Regards
Evan Harris
--
This is the Midrange Systems Technical Discussion (MIDRANGE-L) mailing

list

To post a message email: MIDRANGE-L@xxxxxxxxxxxx
To subscribe, unsubscribe, or change list options,
visit: http://lists.midrange.com/mailman/listinfo/midrange-l
or email: MIDRANGE-L-request@xxxxxxxxxxxx
Before posting, please take a moment to review the archives
at http://archive.midrange.com/midrange-l.

--
This is the Midrange Systems Technical Discussion (MIDRANGE-L) mailing list
To post a message email: MIDRANGE-L@xxxxxxxxxxxx
To subscribe, unsubscribe, or change list options,
visit: http://lists.midrange.com/mailman/listinfo/midrange-l
or email: MIDRANGE-L-request@xxxxxxxxxxxx
Before posting, please take a moment to review the archives
at http://archive.midrange.com/midrange-l.