Re: Remote power up of System i 520

http://firefox-technical-support.blogspot.be/2011/03/how-to-enable-ssl2-in-firefox.html

It is still possible, but disabled by default due to security contraints.
It is known to be broken.


2013/1/2 Jeff Crosby <jlcrosby@xxxxxxxxxxxxxxxx>

Heh. When I search from the about:config page for "ssl2" nothing shows

up.

I'm at Firefox 17.0.1. I assume that's so new that ssl2 is completely
gone.


On Mon, Dec 31, 2012 at 1:30 PM, Mike Buglass <noqnoq@xxxxxxxxxxxx>

wrote:

You could try going to the about:config page in firefox and search on
security.enable and enable ssl2.


DrFranken wrote:

You have a POWER5 server and your web browser is too new.

First try http: instead of https: to see if that works. Try an old
version of Firefox. (You can still download version 3) Or that's

why I

like Plan "B" (the serial cable.)

- Larry "DrFranken" Bolhuis

www.frankeni.com
www.iDevCloud.com
www.iInTheCloud.com


On 12/31/2012 11:30 AM, Jeff Crosby wrote:

I have a cable direct from HMC2 (192.168.3.147) to a laptop.

The IPV4 settings on the laptop are:

IP address 192.168.3.1
Subnet mask 255.255.255.0

Everything else is blank. I can ping 192.168.3.147, but cannot open
https://192.168.3.147

Firefox says: Cannot communicate securely with peer:no common

encryption

algorithms. (Error code: ssl_error_no_cypher_overlap)
Chrome says it timed out.
IE says it cannot display the webpage.

What am I missing?




On Mon, Dec 31, 2012 at 10:42 AM, DrFranken <midrange@xxxxxxxxxxxx>

wrote:

You can use either port, just set the IP address of the PC you're

going

to use appropriately for the selected port.

If it was me, I would use the OTHER port from the one I'm going to
connect to my network so that I could change that port's IP address

and

verify access to it before I disconnected.

- Larry "DrFranken" Bolhuis

www.frankeni.com
www.iDevCloud.com
www.iInTheCloud.com

On 12/31/2012 10:18 AM, Jeff Crosby wrote:

Thanks, Pete. The information says:

ETH0 (T1) 192.168.2.147
ETH1 (T2) 192.168.3.147

which are the defaults. Does this mean the ethernet cable I use

should

get

plugged into either the T1 or T2 jack in the I5?





On Sun, Dec 30, 2012 at 9:53 AM, Pete Massiello - ML <
pmassiello-ml@xxxxxxxxxxxx> wrote:

Jeff,

To find out the address of your ASMI port, on the bezel, go to

Sequence

30

(will have to be in manual mode first), and the 2 addresses are

the

HMC1

and HMC2 port respectively.

Pete

--
Pete Massiello
iTech Solutions
http://www.itechsol.com
http://www.iInTheCloud.com




-----Original Message-----
From: midrange-l-bounces@xxxxxxxxxxxx [mailto:
midrange-l-bounces@xxxxxxxxxxxx] On Behalf Of Jeff Crosby
Sent: Friday, December 28, 2012 3:04 PM
To: Midrange Systems Technical Discussion
Subject: Re: Remote power up of System i 520

Don't laugh at this idea.

2 PCs here can function as LAN Console. Each has 2 NIC cards,

with

the

2nd NIC dedicated to the LAN Console connection. There is a

single

Linksys

switch on top of the System i rack with 3 ethernet cables

attached:

1) To the T5 (I think) jack on the System i (10.10.10.1)
2) To my PC (10.10.10.2)
3) To the office manager's PC (10.10.10.3)

This is a completely isolated network. If I run an ethernet

cable

from

the ASMI to that switch and can figure out the IP address of the

ASMI,

can

I just point a browser from my PC to https://xxx.xxx.xxx.xxxwhere
xxx.xxx.xxx.xxx is the IP address? And then I could RDP to my

desktop

from

home and away we go?



On Fri, Dec 28, 2012 at 2:26 PM, Kirk Goins <kirkgoins@xxxxxxxxx

wrote:

I think this will work and says about $10K for an HMC...
Find the default AMSI/HMC port IP addresses for your system

Attach a

laptop to which ever HMC port you choose using the same IP

subnet

as

the port you are attaching to Open a browser session and log in

to

AMSI Set the other HMC port to an address that is compatible

with

your

local network including Gateway address Cable up that port up to

the

local network and access AMSI In there I believe you can Power

Up

the

Managed System.

.



On Fri, Dec 28, 2012 at 11:18 AM, Jeff Crosby
<jlcrosby@xxxxxxxxxxxxxxxx

wrote:
Short of an HMC, is there any way to remotely power up a

System i

520?

I have LAN Console and Remote Control Panel on my desktop at

work.

Due

to

power issues last week (low voltage from utility) after a power
outage, I changed QPWRRSTIPL to 0 for no power up when power is

restored.

In a future outage that results in my power handling program
shutting

down

the system, I have no recourse to power it up other than 1)

drive

in

to work, or 2) get an HMC, correct?

I can remote from home to my work desktop, but since the

System i

is

powered off, there ain't not no Remote Control Panel.

Thanks.

--
Jeff Crosby
VP Information Systems
UniPro FoodService/Dilgard
P.O. Box 13369
Ft. Wayne, IN 46868-3369
260-422-7531
www.dilgardfoods.com

--
This is the Midrange Systems Technical Discussion (MIDRANGE-L) mailing

list

To post a message email: MIDRANGE-L@xxxxxxxxxxxx
To subscribe, unsubscribe, or change list options,
visit: http://lists.midrange.com/mailman/listinfo/midrange-l
or email: MIDRANGE-L-request@xxxxxxxxxxxx
Before posting, please take a moment to review the archives
at http://archive.midrange.com/midrange-l.

--
Jeff Crosby
VP Information Systems
UniPro FoodService/Dilgard
P.O. Box 13369
Ft. Wayne, IN 46868-3369
260-422-7531
www.dilgardfoods.com

The opinions expressed are my own and not necessarily the opinion of my
company. Unless I say so.
--
This is the Midrange Systems Technical Discussion (MIDRANGE-L) mailing

list

To post a message email: MIDRANGE-L@xxxxxxxxxxxx
To subscribe, unsubscribe, or change list options,
visit: http://lists.midrange.com/mailman/listinfo/midrange-l
or email: MIDRANGE-L-request@xxxxxxxxxxxx
Before posting, please take a moment to review the archives
at http://archive.midrange.com/midrange-l.

--

|_|0|_| Yvan Janssens
|_|_|0|
|0|0|0|
--
This is the Midrange Systems Technical Discussion (MIDRANGE-L) mailing list
To post a message email: MIDRANGE-L@xxxxxxxxxxxx
To subscribe, unsubscribe, or change list options,
visit: http://lists.midrange.com/mailman/listinfo/midrange-l
or email: MIDRANGE-L-request@xxxxxxxxxxxx
Before posting, please take a moment to review the archives
at http://archive.midrange.com/midrange-l.