Ahhhh job security = Keep using IBM SMTP and MSF to send
emails :)
-----Original Message-----
From: midrange-l-bounces@xxxxxxxxxxxx
[mailto:midrange-l-bounces@xxxxxxxxxxxx] On Behalf Of Cyndi
Bradberry
Sent: Monday, July 23, 2012 1:15 PM
To: midrange-l@xxxxxxxxxxxx
Subject: V7R1 Upgrade...SMTP problem
Hi everyone. Over the weekend, we swapped to a new P7 box
running V7R1 from a P6 box running V6R1. Today, I don't have
any email running from our new P7.
I double checked all the SMTP attributes were the same
between the two boxes. I found the MailHubRouter parameter
and put in the same as in my Mail Router. I changed the
attributes of the /tmp folder. I have stopped MSF. And yet
each time I attempt to start SMTP I get the following:
Job 011182/QTCP/QTSMTPSRVD started on 07/23/12 at 11:04:49
in subsystem
QSYSWRK in QSYS. Job entered system on 07/23/12 at
11:04:49.
Job 011182/QTCP/QTSMTPSRVD submitted.
SMTP initialization not successful.
SMTP job ended normally.
Parameter SBS required.
Object QTMSSCHD in QTEMP type *USRSPC deleted.
Object QTMSFLRC in QTEMP type *USRSPC deleted.
Job 011182/QTCP/QTSMTPSRVD ended on 07/23/12 at 11:04:49;
.029 seconds
used; end code 0 .
And the job is listed as Job Log Pending. If I press F1 on
the initialization not successful message:
Message ID . . . . . . : TCP2075 Severity . . . . .
. . : 40
Message type . . . . . : Diagnostic
Date sent . . . . . . : 07/23/12 Time sent . . . .
. . : 11:04:49
Message . . . . : SMTP initialization not successful.
Cause . . . . . : SMTP initialization did not complete
because one of the
SMTP jobs had a problem.
Recovery . . . : Check the job log or the system operator
log for messages
from the SMTP jobs.
There are no messages in the system operator queue. What is
above is the job log.
For the SBS is required message:
Additional Message Information
Message ID . . . . . . : CPD0071 Severity . . . . .
. . : 30
Message type . . . . . : Diagnostic
Date sent . . . . . . : 07/23/12 Time sent . . . .
. . : 11:04:49
Message . . . . : Parameter SBS required.
Cause . . . . . : A required parameter was not specified.
Recovery . . . : Enter a value for parameter SBS.
And if I press F9:
Message ID . . . . . . : CPD0071 Severity . . . . .
. . : 30
Date sent . . . . . . : 07/23/12 Time sent . . . .
. . : 11:04:49
Message type . . . . . : Diagnostic
From . . . . . . . . . : QTCP CCSID . . . . . .
. . : 65535
From program . . . . . . . . . : QCAFLD
From library . . . . . . . . : QSYS
Instruction . . . . . . . . : 12F0
To program . . . . . . . . . . : QTMSSRCD
To library . . . . . . . . . : QTCP
To module . . . . . . . . . : QTMSSRCD
To procedure . . . . . . . . : CDoCLCommand__FPc
To statement . . . . . . . . : 25
Time sent . . . . . . . . . . : 11:04:49.814775
I am trying to figure out what IBM needs me to do. The same
subsystems, jobq's etc are all duplicated from the old
system to the new. We heavily use automated emails so I
need to get this running. I get the same errors on our V7
test LPAR, but everything runs perfectly on the V6 system
still.
Can anyone point me in the right direction ?
Cyndi B.
Boise, ID
--
This is the Midrange Systems Technical Discussion
(MIDRANGE-L) mailing list To post a message email:
MIDRANGE-L@xxxxxxxxxxxx To subscribe, unsubscribe, or change
list options,
visit:
http://lists.midrange.com/mailman/listinfo/midrange-l
or email: MIDRANGE-L-request@xxxxxxxxxxxx Before posting,
please take a moment to review the archives at
http://archive.midrange.com/midrange-l.
midrange.com
