Re: STROBJCVN - Need to interrupt a V6R1M0 conversion

[PaultinNZ <paultormey@xxxxxxxxx>]

Hi Pete,

If you don't mind, I'll definitely look at your program, in CL I presume,
and will definitely tailor it for our production cutover in MAY 2010.

As mentioned earlier, the system eventually came back and completed all
successfully. This test system only has 0.5% of a processor allocated so
once we get to production with the full 4 processors things should be a lot
quicker.


Thanks a ton.

Paul


On 18 April 2010 16:17, Pete Massiello <pmassiello-ml@xxxxxxxxxxxx> wrote:

> Cancel it and restart it, no problem.
>
> I have a program that I wrote (in the V6R1 article) and it is on my
> website,
> which cuts the conversion time down by about 60% of what the IBM ANZOBJCVN
> command will say, by multi-threading.  Use it all the time, and it makes a
> huge difference.
>
>        Pete
>
> Pete Massiello
> iTech Solutions
> http://www.itechsol.com
>
> Add iTech Solutions on Facebook:
> http://www.facebook.com/group.php?gid=126431824120
> Add iTech Solutions on LinkedIn:
> http://www.linkedin.com/groups?gid=2206093
>
>
>
>
> -----Original Message-----
> From: midrange-l-bounces@xxxxxxxxxxxx
> [mailto:midrange-l-bounces@xxxxxxxxxxxx] On Behalf Of Paul Tormey
> Sent: Saturday, April 17, 2010 8:04 PM
> To: midrange-l@xxxxxxxxxxxx
> Subject: STROBJCVN - Need to interrupt a V6R1M0 conversion
>
> In my wisdom, I started the V6R1M0 STROBJCVN (*CONVERT) from my HMC
> Remote 5250 Console. Thoughts of having the system standalone while the
> conversion runs!
>
> This was run just after I had done the upgrade from V5R4M0 using
> PWRDWNSYS using an image catalog. Off course that all completed okay.
> But I suspect, didn't check, that the system is still in restricted mode?
>
> The pre upgrade ANZOBJCVN had been run and said the conversion would run
> for +/- 27 hours. The conversion started at 16:28 Sat 17/04/2010 and
> it's now 12:00 Sun 18/04/2010.
>
> Further reading on the list and redbooks shows that one need not run in
> a 'stand alone' environment.
>
> If I interrupt my HMC session and that ends the running STROBJCVN what
> are the implications?
>
>    1. Can I restart the conversion or would all that has been done be
>      backed out/rolled back?
>   2. I would IPL first so that the system is restarted in 'normal' mode.
>
> Any ideas or recommendations would be appreciated.
> --
> This is the Midrange Systems Technical Discussion (MIDRANGE-L) mailing list
> To post a message email: MIDRANGE-L@xxxxxxxxxxxx
> To subscribe, unsubscribe, or change list options,
> visit: http://lists.midrange.com/mailman/listinfo/midrange-l
> or email: MIDRANGE-L-request@xxxxxxxxxxxx
> Before posting, please take a moment to review the archives
> at http://archive.midrange.com/midrange-l.
>
>
> --
> This is the Midrange Systems Technical Discussion (MIDRANGE-L) mailing list
> To post a message email: MIDRANGE-L@xxxxxxxxxxxx
> To subscribe, unsubscribe, or change list options,
> visit: http://lists.midrange.com/mailman/listinfo/midrange-l
> or email: MIDRANGE-L-request@xxxxxxxxxxxx
> Before posting, please take a moment to review the archives
> at http://archive.midrange.com/midrange-l.