× The internal search function is temporarily non-functional. The current search engine is no longer viable and we are researching alternatives.
As a stop gap measure, we are using Google's custom search engine service.
If you know of an easy to use, open source, search engine ... please contact support@midrange.com.



Ok, now it knows to use Operations LAN Console, but it needs to know to use
the Internal ports, that is why
You need to also do the same for the E1 for enable the embedded Internal
Ethernet ports.

You shouldn't have to wait that long. When the last character in Word 11
goes from a B to a C, it means the last operation (which would have been the
21 after seeing the value you wanted in 11) completed successfully.

You don't have to set it to normal mode, nor IPL again. You should get the
Pop-up screen asking for a password. Your problem is the internal ports
aren't enabled.

Pete

Pete Massiello
iTech Solutions
http://www.itechsol.com

Add iTech Solutions on Facebook:
http://www.facebook.com/group.php?gid=126431824120
Add iTech Solutionw on LinkedIn: http://www.linkedin.com/groups?gid=2206093





-----Original Message-----
From: midrange-l-bounces@xxxxxxxxxxxx
[mailto:midrange-l-bounces@xxxxxxxxxxxx] On Behalf Of Jacob Anderson
Sent: Tuesday, February 09, 2010 4:59 PM
To: 'Midrange Systems Technical Discussion'
Subject: RE: operations console via lan

Okay, so the system was in mode 01, twinax. Aside from feeling like a real
rookie, I think that I am getting somewhere now. I did this numerous
25->26->(65+21+11){3}->(21+11) operations to make it mode 03 for LAN.

I have to wait 3 minutes for it to realize that I changed it, then I'll
reset it to normal mode and do the whole operation of installing the LAN
cable and powering-on the iSeries again.

Progress.....Thanks!

-- jake


-----Original Message-----
From: midrange-l-bounces@xxxxxxxxxxxx
[mailto:midrange-l-bounces@xxxxxxxxxxxx] On Behalf Of Pete Massiello
Sent: Tuesday, February 09, 2010 12:01 PM
To: 'Midrange Systems Technical Discussion'
Subject: RE: operations console via lan

Put it in T5.

Do the 65+21 sequence on the bezel to make sure that you have the
A6xx500y where the xx is "03" for Lan Console. Also, then keep going till I
think it is an "E1" to enable Internal Ports. Otherwise you won't get
connected.

Now, I don't know if this is the same guy with all the ASMI issues
last week, but you need to understand that console connection is NOT the
same TCP/IP address that your PC Clients will connect to.

I highly recommend when doing this that you have a DIRECT cable from
the PC to the T5 port. This way, as you boot your 520 you can see the
Ethernet connection on the PC going up and down (Connecting at 100mb, then
connecting at 1G, etc). This will know you are connected, especially when
you have the dreaded C6004031 (looking for console).

I don't know if Windows Server is supported for Operations Console,
I remember a while back that it wasn't. You are the same guy, as you keep
referring to Eth0 and that is what keeps confusing everyone on your last
posts, as that is an HMC port name, and you will continue to confuse people
if you use that term on this iSeries list.

The PC running Operations Console and the T5 on the iSeries must
(REPEAT MUST) be on the same subnet during the BOOTP process when the client
sends down the config to the T5 port, and the T5 ports accepts this.

Good Luck.

Pete

Pete Massiello
iTech Solutions
http://www.itechsol.com

Add iTech Solutions on Facebook:
http://www.facebook.com/group.php?gid=126431824120
Add iTech Solutionw on LinkedIn: http://www.linkedin.com/groups?gid=2206093





-----Original Message-----
From: midrange-l-bounces@xxxxxxxxxxxx
[mailto:midrange-l-bounces@xxxxxxxxxxxx] On Behalf Of Jacob Anderson
Sent: Tuesday, February 09, 2010 2:04 PM
To: 'Midrange Systems Technical Discussion'
Subject: operations console via lan

Hello,

I am trying to do the initial operations console setup for my 520 power 5.

Windows Server -> v6r1 Client Access, op console version 6.1.0.0 490.6
LAN IP: 192.168.16.20
iSeries Target IP: 192.168.16.30
iSeries Service Name: matches the service name found in the ASMI via
serial connection

Here is what I have done:

1. Powerdown the iSeries
2. Unplug power
3. Plug in RJ45 cat6 cable from LAN port on Win server directly into T6 (LAN
eth0) on iSeries
4. Start operations console on win server
5. Click "connect" on my iSeries node
6. Plugin power to iSeries
7. Wait for front console panel to show SRC codes for boot, happy
8. Return to Win server and wait for op con to respond

Nothing. Op console always says "connecting" but nothing happens. There is
no firewall enabled on the Win server and the cables are directly attached
and properly labeled/configured.

I've tried it on both of the LAN Ethernet ports for the iSeries with the
same result.

I have waited the "20 minutes" as recommended in the op con operations
manual (pg 51 of 128).

Is there something else I need to do to setup the LAN ports, or even get
started, so that I can run the op con on the iSeries?

Note that I have mistakenly plugged in a DHCP managed network in to the
iSeries LAN Ethernet port (eth0) in prior configuration attempts.

Thanks

-- Jake





As an Amazon Associate we earn from qualifying purchases.

This thread ...

Follow-Ups:
Replies:

Follow On AppleNews
Return to Archive home page | Return to MIDRANGE.COM home page

This mailing list archive is Copyright 1997-2024 by midrange.com and David Gibbs as a compilation work. Use of the archive is restricted to research of a business or technical nature. Any other uses are prohibited. Full details are available on our policy page. If you have questions about this, please contact [javascript protected email address].

Operating expenses for this site are earned using the Amazon Associate program and Google Adsense.