Re: Problem with Printer Definition setup by a newbie to i5 -- MIDRANGE-L

have you tried to setup a remote output queue for this device and then use
raw, I bet the printerserver isn't setup to support 9100.

On Thu, Oct 8, 2009 at 7:41 AM, Panayiotis Petrou <
panayiotis.petrou@xxxxxxxxxxxxxxxxxxxx> wrote:

The IBM 6400 printer we are trying to setup is connected to the LAN thru a
Micronet SP760 print server (parallel connection) on LPT1.

I tried changing the port 9100 but we get an error on the IP address/port.
I also tried the suggestions below and I got the following errors.

5722SS1 V5R4M0 060210 Job Log
S65509EB 08/10/09 14:35:15 Page 1
Job name . . . . . . . . . . : WTR_6400 User . . . . . . :
QSPLJOB Number . . . . . . . . . . . : 016465
Job description . . . . . . : QSPLPRTW Library . . . . . :
QGPL
MSGID TYPE SEV DATE TIME FROM PGM
LIBRARY INST TO PGM LIBRARY INST
CPF1124 Information 00 08/10/09 14:35:15.044056 QWTPIIPP
QSYS 066E *EXT *N
Message . . . . : Job
016465/QSPLJOB/WTR_6400 started on 08/10/09 at
14:35:14 in subsystem QSPL in QSYS.
Job entered system on 08/10/09 at
14:35:14.

*NONE Request 08/10/09 14:35:15.044528 QWTSCSBJ
*N QCMD QSYS 0194
From user . . . . . . . . . : D813

Message . . . . : -CALL QSYS/QSPWTRM1

CPD401A Diagnostic 40 08/10/09 14:35:15.331888 QWPSNMPD
QSYS *STMT QWPSNMPD QSYS *STMT
From module . . . . . . . . : WPSNMPD

From procedure . . . . . . :
Initialize_Driver
Statement . . . . . . . . . : 131

To module . . . . . . . . . : WPSNMPD

To procedure . . . . . . . : _C_pep

Statement . . . . . . . . . : *N

Message . . . . : Could not establish
SNMP communications with device
WTR_6400.

Cause . . . . . : Was not able to
establish SNMP communications with device
WTR_6400. The reason code is 2. The
reason codes and their meanings are as
follows: 1 - The device appears to be
an SNMP device but not a printer. 2 -
The device appears to be an SNMP
device but does not support the required
level of an industry standard SNMP
protocol. 3 - Communication with the
device timed out. This could occur
because of heavy network traffic, the
device is not an SNMP device, or the
read community name set on the device
is different than expected. Recovery
. . . : Make sure that the device is
a printer that supports the industry
standard SNMP protocol and that the
read community name is set correctly.
Then try the operation again.
CPF3473 Escape 60 08/10/09 14:35:15.332368 QSPOPNWX
QSYS 0246 QCMD QSYS 01C7
Message . . . . : Writer
016465/QSPLJOB/WTR_6400 did not end normally.
Recovery . . . : See the previously
listed messages to determine cause of
the writer failure. Correct any
errors and start the writer again.
CPC2402 Completion 50 08/10/09 14:35:15.339064 QCMD
QSYS 0668 *EXT *N
Message . . . . : Job ended. Cancel
message received at command processor.
Cause . . . . . : A message with a
severity equal to or exceeding the end
severity was received at the command
processor. Recovery . . . : See the

Panayiotis (Pete) Petrou
zVSE and Websphere MQ System Administration
Information Technology Division
Bank Of Cyprus
Tel 357-22-12-8473

-----Original Message-----
From: midrange-l-bounces@xxxxxxxxxxxx
[mailto:midrange-l-bounces@xxxxxxxxxxxx] On Behalf Of
smorrison@xxxxxxxxxxxxxxxxxxx
Sent: Wednesday, October 07, 2009 9:54 PM
To: Midrange Systems Technical Discussion
Subject: Re: Problem with Printer Definition setup by a newbie to i5

Jack mentioned changing the port to 9100. Our 6400 is set to Workstation
Customization Object = *NONE, and System Drive Program = *IBMSNMPDRV. I'm
not sure what you'll get trying to use HPPJLDRV.

Steve
- -
Steven Morrison
Fidelity Express

"Panayiotis
Petrou"
<panayiotis.petro To
u@xxxxxxxxxxxxxxx <midrange-l@xxxxxxxxxxxx>
s.com> cc
Sent by:
midrange-l-bounce Subject
s@xxxxxxxxxxxx Problem with Printer Definition
setup by a newbie to i5

10/07/2009 10:42
AM

Please respond to
Midrange Systems
Technical
Discussion
<midrange-l@midra
nge.com>

We have an IBM 6400 line printer attached to a print server that we
currently use to print from our VSE system via TCP/IP LPR.

I have attempted to try and define a Printer device description on an i5
(see device description below) but I am not able to print.

Any help will be greatly appreciated.

The messages I am getting are as follows:

5722SS1 V5R4M0 060210 Job Log
S65509EB 07/10/09 12:38:21 Page 1

Job name . . . . . . . . . . : WTR_6400 User . . . . . . :
QSPLJOB Number . . . . . . . . . . . : 016337

Job description . . . . . . : QSPLPRTW Library . . . . . :
QGPL

SGID TYPE SEV DATE TIME FROM PGM
LIBRARY INST TO PGM LIBRARY INST

PF1124 Information 00 07/10/09 12:38:06.183544 QWTPIIPP
QSYS 066E *EXT *N

Message . . . . : Job
016337/QSPLJOB/WTR_6400 started on 07/10/09 at

12:38:06 in subsystem QSPL in QSYS.
Job entered system on 07/10/09 at

12:38:06.

NONE Request 07/10/09 12:38:06.184096 QWTSCSBJ
*N QCMD QSYS 0194

From user . . . . . . . . . : D813

Message . . . . : -CALL QSYS/QSPWTRM1

PD338D Diagnostic 40 07/10/09 12:38:21.214888 QWPPJLDR
QSYS *STMT QWPPJLDR QSYS *STMT

From module . . . . . . . . : WPPJLDR

From procedure . . . . . . :
Socket_Recv

Statement . . . . . . . . . : 40

To module . . . . . . . . . : WPPJLDR

To procedure . . . . . . . : _C_pep

Statement . . . . . . . . . : *N

Message . . . . : An error occurred
while receiving data.

More...

Cause . . . . . : A communications
error occurred while receiving data from

remote device at RMTLOCNAME
10.1.103.186. The error code is 3426. This error

can also occur when the system
attempts to print to the remote device after

it has been powered off and on
while
the printer writer remains active.

Recovery . . . : Try the request
again. If the problem continues, end

TCP/IP using the End TCP/IP
(ENDTCP)
command, start TCP/IP by using the

Start TCP/IP (STRTCP) command, and
then try the request again.

CPF3473 Escape 60 07/10/09 12:38:21.216408
QSPOPNWX
QSYS 0246 QCMD QSYS 01C7

Message . . . . : Writer
016337/QSPLJOB/WTR_6400 did not end normally.

Recovery . . . : See the
previously
listed messages to determine cause of

the writer failure. Correct any
errors and start the writer again.

CPC2402 Completion 50 07/10/09 12:38:21.235840 QCMD
QSYS 0668 *EXT *N

Message . . . . : Job ended. Cancel
message received at command processor.

Cause . . . . . : A message with a
severity equal to or exceeding the end

severity was received at the
command
processor. Recovery . . . : See the

messages previously listed to
determine the message that caused the job to

be ended. Correct the errors, and
then try the request again.

CPC2191 Completion 00 07/10/09 12:38:21.238544
QLIDLOBJ
QSYS 051B QLICLLIB QSYS 05DC

Message . . . . : Object SPLAPISPJL
in QTEMP type *USRSPC deleted.

Device description . . . . . . . . : WTR_6400

Option . . . . . . . . . . . . . . : *BASIC

Category of device . . . . . . . . : *PRT

Device class . . . . . . . . . . . : *LAN

Device type . . . . . . . . . . . : 3812

Device model . . . . . . . . . . . : 1

LAN attachment . . . . . . . . . . : *IP

Port number . . . . . . . . . . . : 515

Physical attachment . . . . . . . : *DIRECT

Online at IPL . . . . . . . . . . : *NO

Font:

Identifier . . . . . . . . . . . : 11

Point size . . . . . . . . . . . : *NONE

Form feed . . . . . . . . . . . . : *AUTOCUT

Separator drawer . . . . . . . . . : *FILE

Separator program . . . . . . . . : *NONE

Printer error message . . . . . . : *INFO

Message queue . . . . . . . . . . : *CTLD

Current message queue . . . . . . : QSYSOPR

Library . . . . . . . . . . . . : QSYS

Activation timer . . . . . . . . . : 170

Inactivity timer . . . . . . . . . : *SEC15

Line speed . . . . . . . . . . . . : 19200

Word length . . . . . . . . . . . : 8

Type of parity . . . . . . . . . . : *NONE

Stop bits . . . . . . . . . . . . : 1

Host print transform . . . . . . . : *YES

Manufacturer type and model . . . : *IBM6400

Paper source 1 . . . . . . . . . . : *CONT132

Paper source 2 . . . . . . . . . . : *NONE

Envelope source . . . . . . . . . : *NONE

ASCII code page 899 support . . . : *YES

Image configuration . . . . . . . : *NONE

Character identifier . . . . . . . : *SYSVAL

Remote location:

Name or address . . . . . . . . : 10.1.103.186

Workstation customizing object . . : QWPIBM64XX

Library . . . . . . . . . . . . : *LIBL

User-defined object . . . . . . . : *NONE

Object type . . . . . . . . . . : *NONE

Data transform program . . . . . . : *NONE

System driver program . . . . . . : *HPPJLDRV

Allocated to:

Job name . . . . . . . . . . . . . : *NONE

User . . . . . . . . . . . . . . :

Number . . . . . . . . . . . . . :

Published . . . . . . . . . . . . : *NO

Publishing information:

Support duplex . . . . . . . . . : *UNKNOWN

Support color . . . . . . . . . : *UNKNOWN

Pages per minute black . . . . . : *UNKNOWN

Pages per minute color . . . . . : *UNKNOWN

Location . . . . . . . . . . . . : *BLANK

Data streams supported . . . . . : *UNKNOWN

Text . . . . . . . . . . . . . . . : IBM6400 On 3rd floor Platy

Panayiotis (Pete) Petrou

zVSE and Websphere MQ System Administration

Information Technology Division

Bank Of Cyprus

Tel 357-22-12-8473

--
This is the Midrange Systems Technical Discussion (MIDRANGE-L) mailing list
To post a message email: MIDRANGE-L@xxxxxxxxxxxx
To subscribe, unsubscribe, or change list options,
visit: http://lists.midrange.com/mailman/listinfo/midrange-l
or email: MIDRANGE-L-request@xxxxxxxxxxxx
Before posting, please take a moment to review the archives
at http://archive.midrange.com/midrange-l.

Confidentiality Statement: This electronic mail transmission is
confidential, may be privileged and should be read or retained only by the
intended recipient. If you have received this transmission in error, please
notify the sender immediately and delete it from your system.
--
This is the Midrange Systems Technical Discussion (MIDRANGE-L) mailing list
To post a message email: MIDRANGE-L@xxxxxxxxxxxx
To subscribe, unsubscribe, or change list options,
visit: http://lists.midrange.com/mailman/listinfo/midrange-l
or email: MIDRANGE-L-request@xxxxxxxxxxxx
Before posting, please take a moment to review the archives
at http://archive.midrange.com/midrange-l.

--
This is the Midrange Systems Technical Discussion (MIDRANGE-L) mailing
list
To post a message email: MIDRANGE-L@xxxxxxxxxxxx
To subscribe, unsubscribe, or change list options,
visit: http://lists.midrange.com/mailman/listinfo/midrange-l
or email: MIDRANGE-L-request@xxxxxxxxxxxx
Before posting, please take a moment to review the archives
at http://archive.midrange.com/midrange-l.