RE: TCP/IP will not start after V6R1 Upgrade

Update fyi, I ipl'ed the system on the A side & everything appears to
come up.

Next step, download the latest cume, load it, & see if this works.

At least I have tomorrow to figure it out.

I also noticed that IPV6 already exists on the V5R4 system and is
started automatically anyway.

Thanks.
James Salter
Systems Programmer
American Cast Iron Pipe Company
phone (205) 325-3033
fax (205) 307-3833


-----Original Message-----
From: Salter, James
Sent: Saturday, May 30, 2009 7:22 PM
To: 'midrange-l@xxxxxxxxxxxx'
Subject: TCP/IP will not start after V6R1 Upgrade

I have upgraded development to V6R1 and I cannot start TCP.
None of my interfaces will work & none of the TCP servers will start.

I am on cume level 8365. I know that there was a new one that came out
a few weeks ago, but I cannot load it easily with TCP down & the
netservers down.

The QSYS/QTCPWRK job has the following errors below.

Any ideas? I will make a call to IBM in the morning, but just wondering
if anyone else experienced this.

Also, can IPV6 & IPV4 both reside at the same time? It looks like it
installed the IPV6 stuff without me realizing it.

I am going to browse the Memo to Users once again & the technical db's
to see if I can find anything on this.


40 05/30/09 14:35:20.795604 < 00024C
QTOCTCPIP
From Program . . . . . . . : cfscvov

To module . . . . . . . . . : TOIPIFCUTL

To procedure . . . . . . . : SETUP_QTCPIP_OBJECTS

Statement . . . . . . . . . : 2638

Message . . . . : Tried to refer to all or part of an object that no
long
exists.

Cause . . . . . : The most common cause is that a stored address to
an
object is no longer correct because that object was deleted or part
of th
object was deleted.

30 05/30/09 14:35:20.795691 QTOCSTCP QSYS 0CA0
QTOCWORK
To module . . . . . . . . . : QTOCWORK

To procedure . . . . . . . : main

Statement . . . . . . . . . : 47

Message . . . . : TCP/IP currently active.

Cause . . . . . : TCP/IP has been previously started and is already
active

40 05/30/09 14:35:20.795994 QMHSNDPM QSYS 0C05 QLEAWI

To module . . . . . . . . . : QLEDEH

To procedure . . . . . . . : Q LE leDefaultEh

Statement . . . . . . . . . : 204

Message . . . . : Value for call stack counter parameter not valid.

Cause . . . . . : The value 3, specified for call stack counter
parameter
is not valid. The value was specified in parameter number 7 on the
API.
Recovery . . . : Correct the value for call stack counter
parameter an
try the request again. This value must be greater than or equal to 0
but
cannot be larger than the number of entries on the call stack.

30 05/30/09 14:35:20.796084 QLEAWI QSYS *STMT
QTOCWORK
From module . . . . . . . . : QLETOOL

From procedure . . . . . . : Q LE CPF24A3_handler

Statement . . . . . . . . . : 9

To module . . . . . . . . . : QTOCWORK

To procedure . . . . . . . : _CXX_PEP__Fv

Statement . . . . . . . . . : *N

Message . . . . : Application error. TCP1A04 unmonitored by
QTOCWORK at
statement 0000000047, instruction X'0000'.

Cause . . . . . : The application ended abnormally because an
exception
occurred and was not handled. The name of the program to which the

unhandled exception is sent is QTOCWORK QTOCWORK main. The program
was
stopped at the high-level language statement number(s) 0000000047 at
the
time the message was sent. If more than one statement number is
shown, t
program is an optimized ILE program. Optimization does not allow a
singl
statement number to be determined. If *N is shown as a value, it
means t
real value was not available. Recovery . . . : See the low level
messa
previously listed to locate the cause of the exception. Correct any
erro
and then try the request again.

50 05/30/09 14:35:20.797293 QWTPITP2 QSYS 0609 *EXT


Thanks.
James Salter
Systems Programmer
American Cast Iron Pipe Company
phone (205) 325-3033
fax (205) 307-3833

_________Confidentiality Notice_______________________
This e-mail and any files transmitted with it is
confidential and is intended solely for the use of
the individual(s) or entity(ies) to whom this e-mail
is addressed. If you are not the intended recipient
or the person responsible for delivering the e-mail
to the intended recipient, be advised that you have
received this e-mail in error, and that any use,
disclosure, dissemination, forwarding, printing,
retention or copying of this e-mail is strictly
prohibited. If you have received this e-mail in
error, please immediately return this e-mail to
the sender and delete the e-mail from your system.
Thank you.