RE: ECOM170 system on the blink

You might check the job logs of those jobs that ended just to see what
they might indicate.  It could be a failed cache as mentioned else where
or a rogue job or situation.  I'd check on those items I mentioned
before and see if you see anything out of the ordinary.  WRKACTJOB is
not the most accurate but if you don't have WRKSYSSTS (comes with
performance tools) it will have to do.  Open it, run it for at least a
minute, sort it by CPU utilization and see what you get.  On DSPSYSSTS
look for high fault rates or any wait-inel numbers.  On WRKDSKSTS look
for high disk utilization - one disk or many....again, not knowing what
you have normally makes it hard to say what would be bad.  In my world
all of my drives operate under a 15% utilization.  Just don't take a 5
second snapshot - let it run for at least 60 seconds or more.

-----Original Message-----
From: midrange-l-bounces@xxxxxxxxxxxx
[mailto:midrange-l-bounces@xxxxxxxxxxxx] On Behalf Of Dwayne Allison
Sent: Wednesday, June 21, 2006 8:57 AM
To: Midrange Systems Technical Discussion
Subject: RE: ECOM170 system on the blink


Can you clarify about the system kicking you off?  
1) I did a DBU on a file and it tried to open the file and after five
minutes of trying to open, my session ended.  I had to log back on again
2) I was coding a program in one session and went to another session to
check a spool file.  I put a 5 on the spool file and after about 3
minutes of trying to open the spool file my session ended (both of them)
3) I was trying to look at a 2 page spool file and it took about 5
minutes before it opened.


-----Original Message-----
From:
midrange-l-bounces+dwayne.allison=affirmativeinsurance.com@xxxxxxxxxxxx
[mailto:midrange-l-bounces+dwayne.allison=affirmativeinsurance.com@midra
nge.com] On Behalf Of Crump, Mike
Sent: Wednesday, June 21, 2006 7:39 AM
To: Midrange Systems Technical Discussion
Subject: RE: ECOM170 system on the blink

Dwayne,

Can you clarify about the system kicking you off?  I am assuming you
mean that while signed on you session might hang or you get kicked back
to the signon screen?

Most of the time poor system performance comes to very hot cpu, memory
demand problems, or disk performance.  Sometimes these can be affected
by a single bad job.  As your system is in a slow period I would check
the CPU utilization (either through WRKACTJOB or WRKSYSACT), memory
demand via DSPSYSSTS, and disk utilization via WRKDSKSTS.  Are you
running any performance data collection during this time frame?

CPU - look for jobs taking a high level of CPU%, especially those jobs
with a high run priority like an interactive job.

Memory - check your page fault numbers.

Disk - look at your disk drive utilization.  See if it is high - this
could even just be one drive.  I don't know what is normal for you so
you will have to interpret the results yourself.  

If you are having interactive jobs ending I would inspect your job log
for any information and possibly also check the QSYSOPR message queue
for anything that might look suspicious.

Also, when you indicate slow I am assuming that interactive response
get's sluggish?  Batch jobs seem to be running ok?

-----Original Message-----
From: midrange-l-bounces@xxxxxxxxxxxx
[mailto:midrange-l-bounces@xxxxxxxxxxxx] On Behalf Of Dwayne Allison
Sent: Wednesday, June 21, 2006 7:51 AM
To: Midrange Systems Technical Discussion
Subject: ECOM170 system on the blink

Good Morning,

 

 

Our ECOM170 box has become slow at time and it sometimes kicks us off
the system.  We check the system status and we are at 77 %.