|
Tom I handle part of the problem by doing a CHKTAP before the delay job, so I am shure a readable tape is in the tapedrive before leaving the building. You can also do the INZTAP before the delay. Maybe this helps. Groetjes (Greetings) =========================================================== Name: Eduard van den Braken E-mail: e.vd.braken@xxxxxxxxx Town: Leusden -- the Netherlands Homepage: http://home.hccnet.nl/e.vd.braken/ =========================================================== -----Oorspronkelijk bericht----- Van: midrange-l-bounces@xxxxxxxxxxxx [mailto:midrange-l-bounces@xxxxxxxxxxxx] Namens Tom Jedrzejewicz @ San Pedro Verzonden: dinsdag 11 maart 2003 17:58 Aan: midrange-l@xxxxxxxxxxxx Onderwerp: MONMSG not monitoring Folks -- model 820 V5R1 The following code is run from the console daily for our backup . . . DLYJOB RSMTIME('23:30:00') ENDSYS DELAY(120) MONMSG MSGID(CPF0000) DLYJOB DLY(180) INZTAP DEV(TAP01) NEWVOL(DAILY) NEWOWNID(CFP) + CHECK(*NO) MONMSG MSGID(CPF0000 CPA0000) DLYJOB DLY(60) --> followed by the various save commands STRSBS SBSD(QCTL) occasionally there will be a problem with the tape, or a failure to put one in, or a write-protected tape. Last night, the INZTAP failed, and the system waited for . The following message was in the log. Additional Message Information Message ID . . . . . . : CPA4086 Severity . . . . . . . : 99 Message type . . . . . : Inquiry Date sent . . . . . . : 03/10/03 Time sent . . . . . . : 23:34:02 Message . . . . : Device TAP01 was not ready or next volume was not loaded. (C R) Cause . . . . . : Either the device TAP01 is not ready or the next tape volume is not loaded on TAP01. Recovery . . . : Do one of the following: -- Type C to cancel processing. -- Make device TAP01 ready, and type R to try the open operation again. -- Put the next volume on device TAP01, and type R to try the open operation again. My question is . . why did the MONMSG on the INZTAP not trap this error and continue on? I want to add code to have an email generated, but if the error is not caught that code is useless. TIA -- Tom J. THIS MESSAGE IS INTENDED ONLY FOR THE USE OF THE INDIVIDUAL OR ENTITY TO WHICH IT IS ADDRESSED AND MAY CONTAIN INFORMATION THAT IS PRIVILEGED, CONFIDENTIAL AND EXEMPT FROM DISCLOSURE UNDER APPLICABLE LAW. If the reader of this message is not the intended recipient, or the employee or agent responsible for delivering the message to the intended recipient, you are hereby notified that any dissemination, distribution, copying, downloading, storing or forwarding of this communication is prohibited. If you have received this communication in error, please notify us immediately via email and delete the message from your computer files and/or data base. Thank you. _______________________________________________ This is the Midrange Systems Technical Discussion (MIDRANGE-L) mailing list To post a message email: MIDRANGE-L@xxxxxxxxxxxx To subscribe, unsubscribe, or change list options, visit: http://lists.midrange.com/mailman/listinfo/midrange-l or email: MIDRANGE-L-request@xxxxxxxxxxxx Before posting, please take a moment to review the archives at http://archive.midrange.com/midrange-l.
As an Amazon Associate we earn from qualifying purchases.
This mailing list archive is Copyright 1997-2024 by midrange.com and David Gibbs as a compilation work. Use of the archive is restricted to research of a business or technical nature. Any other uses are prohibited. Full details are available on our policy page. If you have questions about this, please contact [javascript protected email address].
Operating expenses for this site are earned using the Amazon Associate program and Google Adsense.
midrange.com
