|
Interesting. I noticed that too and checked qpsplprt/qsys as well. I changed both qsysprt/qsys and qpsplprt/qsys to handle 198 wide, 66 long, 60 overflow, and 16.7 cpi to no avail. I regenerated the reports and still get the error. I suspect that there are some s36 control codes embedded in the report that the iSeries cannot handle. What do you think? Jerry PS: I reviewed the wrkm36cfg per Paul T. and found it to be ok. J Jerome Draper, Trilobyte Software Systems, since 1976 Network and Connectivity Specialist -- Mac's, LAN's, PC's, Windows, Linux, Sun, and AS/400 Representing Synapse, CLI, Nlynx, Perle, Lucent, 3Com and Others ..... http://www.trilosoft.com - (415) 457-3431 - (415) 258-1658fax - jdraper@trilosoft.com ----- Original Message ----- From: <thomas@inorbit.com> To: <MIDRANGE-L@midrange.com> Sent: Friday, July 20, 2001 7:13 PM Subject: Re: 5219/3812 *M36/iSeries outq issue > Jerome: > > You typed "qsys/qsysprt" but every message you've included has referred to "QPSPLPRT in QSYS". Was that a typo? > > Tom Liotta > > On Thu, 19 July 2001, "Jerome Draper" wrote: > > > > > If I respond with I then I get a new message on this problem which points to > > page width. I set qsys/qsysprt to 198 and re-ran the report to no avail. > > Stuck! > > > > Jerry > > > > Display Messages > > System: S101AF5R > > Queue . . . . . : RWFF01D1 Program . . . . : *DSPMSG > > Library . . . : QSYS Library . . . : > > Severity . . . : 00 Delivery . . . : *NOTIFY > > > > Type reply (if required), press Enter. > > Writer 159889/QSPLJOB/RWFF01P1 started. > > Attributes of file ORDER not supported for device RWFF01P1. (C G T H I) > > Reply . . : I > > Page width of file QPSPLPRT in QSYS not supported on device RWFF01P1. > > File ORDER held by writer RWFF01P1 on output queue RWFF01P1 in QUSRSYS. > > > > > > Jerome Draper, Trilobyte Software Systems, since 1976 > > Network and Connectivity Specialist -- Mac's, LAN's, PC's, Windows, Linux, > > Sun, and AS/400 > > Representing Synapse, CLI, Nlynx, Perle, Lucent, 3Com and Others ..... > > (415) 457-3431; (415) 258-1658fax; jdraper@trilosoft.com > > > > > > ----- Original Message ----- > > From: Jerome Draper <jdraper@trilosoft.com> > > To: <MIDRANGE-L@midrange.com> > > Sent: Thursday, July 19, 2001 2:28 PM > > Subject: Re: 5219/3812 *M36/iSeries outq issue > > > > > > > Update: It is apparantly the width of the report that is causing the > > > problem. I checked the size of prtf qsys/qsysprt and found it to be 150 > > and > > > cpi 15 so i changed it to 198 and cpi 10 (normal) but to no avail. > > > > > > JErry > > > > > > Jerome Draper, Trilobyte Software Systems, since 1976 > > > Network and Connectivity Specialist -- Mac's, LAN's, PC's, Windows, Linux, > > > Sun, and AS/400 > > > Representing Synapse, CLI, Nlynx, Perle, Lucent, 3Com and Others ..... > > > http://www.trilosoft.com; (415) 457-3431; (415) 258-1658fax; > > > jdraper@trilosoft.com > > > > > > > > > > I have a case were an app is running as an *M36 guest and a printer (P9) > > > is > > > > configured to print directly to an AS400 outq (wrkm36cfg) which bypasses > > > the > > > > S36 spooler. This works fine for common reports. > > > > > > > > (FYI: I have P9 set to be a 5219 printer (I tried a 5224 and a 5219 but > > > it > > > > didn't work either.) > > > > > > > > Of course the one important report the boss needs and the reason for > > this > > > > project is special. It has a FORMS stmt is the S36 OCL that changes the > > > CPI > > > > to 15 (only 10 and 15 are allowed). When the report lands in the AS400 > > > outq > > > > it is has a CPI of 10 and a page width of 160 which makes for an illegal > > > > paper size for a 3812 laser printer. > > > > > > > > Oh woe! We can never print the report as we get an error message: > > > > > > > > Message ID . . . . . . : CPA3388 > > > > Date sent . . . . . . : 07/19/01 Time sent . . . . . . : > > > > 13:06:34 > > > > > > > > Message . . . . : Attributes of file ORDER not supported for device > > > > RWFF01P1. (C G T H I) > > > > > > > > Cause . . . . . : Writer RWFF01P1 found attributes of file ORDER > > number > > > 2 > > > > job 159148/QUSER/QNURHMED on output queue RWFF01P1 in library QUSRSYS > > > > that > > > > are not supported for device RWFF01P1. The error code, or codes, are > > 1. > > > > The > > > > error codes and their meaning are as follows: > > > > 1 - Page size of file not supported on device. > > > > 2 - Device type of file not supported on device. > > > > 3 - Lines per inch (LPI) of file not supported on device. > > > > 4 - Special device requirements of file not supported on device. > > > > Recovery . . . : Enter C to cancel the writer and G or T to process > > > the > > > > file. > > > > If G is entered, the results may not be what is expected because the > > > print > > > > lines can be folded and the file will be printed with the page size and > > > the > > > > attributes from file QPSPLPRT in library QSYS. > > > > If T is entered, the results may not be what is expected because the > > > print > > > > lines can be truncated and the file will be printed with the page size > > and > > > > the attributes from file QPSPLPRT in library QSYS. > > > > Both G and T may cause the actual number of pages produced by the > > writer > > > > to be more than the original number of spooled pages. > > > > Enter H to hold file ORDER on the output queue and produce the next > > > file. > > > > Enter I to ignore that attributes of file ORDER are not supported for > > > > device RWFF01P1 and proceed as if they were supported. > > > > Possible choices for replying to message . . . . . . . . . . . . . . . : > > > > C -- Cancel writer > > > > G -- Process file on device > > > > H -- Hold file and process next file > > > > T -- Process file with print lines truncated > > > > I -- Ignore that attributes are not supported. > > > > Technical description . . . . . . . . : When the G or T reply is > > taken, > > > > the > > > > writer will use significantly more processing unit resources to > > reformat > > > > the > > > > spooled output file. The extra processing unit usage can adversely > > > affect > > > > other jobs in the system. > > > > > > > > Help! > > > > > > > > > +--- > > > | This is the Midrange System Mailing List! > > > | To submit a new message, send your mail to MIDRANGE-L@midrange.com. > > > | To subscribe to this list send email to MIDRANGE-L-SUB@midrange.com. > > > | To unsubscribe from this list send email to > > MIDRANGE-L-UNSUB@midrange.com. > > > | Questions should be directed to the list owner/operator: > > david@midrange.com > > > +--- > > > > > > > +--- > > | This is the Midrange System Mailing List! > > | To submit a new message, send your mail to MIDRANGE-L@midrange.com. > > | To subscribe to this list send email to MIDRANGE-L-SUB@midrange.com. > > | To unsubscribe from this list send email to MIDRANGE-L-UNSUB@midrange.com. > > | Questions should be directed to the list owner/operator: david@midrange.com > > +--- > > -- > Tom Liotta > The PowerTech Group, Inc. > 19426 68th Avenue South > Kent, WA 98032 > Phone 253-872-7788 > Fax 253-872-7904 > http://www.400Security.com > > > ___________________________________________________ > The ALL NEW CS2000 from CompuServe > Better! Faster! More Powerful! > 250 FREE hours! Sign-on Now! > http://www.compuserve.com/trycsrv/cs2000/webmail/ > > > > > +--- > | This is the Midrange System Mailing List! > | To submit a new message, send your mail to MIDRANGE-L@midrange.com. > | To subscribe to this list send email to MIDRANGE-L-SUB@midrange.com. > | To unsubscribe from this list send email to MIDRANGE-L-UNSUB@midrange.com. > | Questions should be directed to the list owner/operator: david@midrange.com > +--- > +--- | This is the Midrange System Mailing List! | To submit a new message, send your mail to MIDRANGE-L@midrange.com. | To subscribe to this list send email to MIDRANGE-L-SUB@midrange.com. | To unsubscribe from this list send email to MIDRANGE-L-UNSUB@midrange.com. | Questions should be directed to the list owner/operator: david@midrange.com +---
As an Amazon Associate we earn from qualifying purchases.
This mailing list archive is Copyright 1997-2025 by midrange.com and David Gibbs as a compilation work. Use of the archive is restricted to research of a business or technical nature. Any other uses are prohibited. Full details are available on our policy page. If you have questions about this, please contact [javascript protected email address].
Operating expenses for this site are earned using the Amazon Associate program and Google Adsense.