• Subject: Re: AFP Printing
  • From: Paul Tykodi <paul@xxxxxxxxxxxxxxxx>
  • Date: Wed, 13 Oct 1999 21:27:29 -0400

Dear Buck and Paul,

The transform buffer message is coming from the AS/400 operating system telling 
you that the amount of system memory assigned to the QSPL subsystem is too 
small to allow for conversion of the *AFPDS file to an HP PCL equivalence.

If you check the knowledge base on the http://www.as400service.ibm.com web site 
in the Print category for host print transform, you should find a couple of 
documents that include suggestions regarding amounts of memory to apply to QSPL 
to solve problems of this nature.

HTH

/Paul
--
Paul Tykodi, Technical Director                      E-mail: 
paul@intermate-us.com 
Intermate US Inc.                                     Tel: 603-431-0606
140 Congress St., #2                                    Fax: 603-436-6432
Portsmouth, NH  03801-4019
 

Date:   Tue, 12 Oct 1999 10:35:35 -0400
From:   Buck Calabro <mcalabro@commsoft.net>
Subject:        RE: AFP Printing

Paul,
Did you get anywhere with this?  I suspect that the 16megs of printer memory is 
too small.  Also, are you using device support or remote writer?
Buck Calabro
Aptis; Albany, NY
mailto:Buck.Calabro@aptissoftware.com

> -----Original Message-----
> From: PaulMmn 
> Sent: Friday, October 08, 1999 12:49 AM
> To:   MIDRANGE-L@midrange.com
> Subject:      AFP Printing
> 
> It's neat--  front and back overlays to create special forms.
> 
> Except--  I keep overstuffing a buffer somewhere.  I can only get a few
> pages to print before the writer shuts down.
> 
> I'm using a new HP 4050 with duplex unit, total 16 Meg of memory, jet
> direct card.  Should have plenty of room.
> 
> The data stream is *AFPDS.
> 
> I'm getting a message,  CPF6DF9:  "Transformed data buffer too small."
> 
>       'The transformed data buffer of 4,000,000 bytes is too small to
> hold the
>       4,347,175 bytes of transformed data that is available.  Only
> 4,000,000
>       bytes of data have been copied to the transformed data buffer.  The
> remaining
>       transformed data is lost.'
> 
>       'Recovery:  Increase the size of the transformed data buffer and
> transform the
>       spooled file again.'
> 
> Well.  I have not been able to locate the *&%*(^&(%^ buffer to increase
> its
> size.   AARRRRGGGGHHHH!!
> 
> I have tried this with different spool files.  One file stops printing
> after 1 duplex page, one after about 14.  I suspect this is not a
> limitation of the printer.
> 
> The overlays are front: about 37K bytes.  back: 138K bytes (the back is
> set of 'Terms & Conditions').
> 
> Other than decreasing the transformed data by 347,175 bytes, what can I
> do?
> 
> OK, I'll call Support Line again tomorrow...
> 
> --Paul E Musselman
> 
+---

+---
| This is the Midrange System Mailing List!
| To submit a new message, send your mail to MIDRANGE-L@midrange.com.
| To subscribe to this list send email to MIDRANGE-L-SUB@midrange.com.
| To unsubscribe from this list send email to MIDRANGE-L-UNSUB@midrange.com.
| Questions should be directed to the list owner/operator: david@midrange.com
+---

This thread ...


Follow On AppleNews
Return to Archive home page | Return to MIDRANGE.COM home page

This mailing list archive is Copyright 1997-2019 by midrange.com and David Gibbs as a compilation work. Use of the archive is restricted to research of a business or technical nature. Any other uses are prohibited. Full details are available on our policy page. If you have questions about this, please contact [javascript protected email address].