Re: CA Windows 95< -- MIDRANGE-L

Alan Pruitt wrote:
> 
> <  Pete, Neil, Guy and Tim responds:
> 
> < I assume that since you are working with IBM, you have already made sure 
>that
> < you have run STRHOSTSVR.  What does the joblog of QZDASRVSD say?
> 
> Thank for the responses, It appears that the setup is correct.
> The routing entries are correct for subsystem qserver.
> STRHOSTSVR *ALL has been ran.  Quser profile is okay and not expired.
> I am running the V3R1M2 version. I have done a netstat and everything appears
> okay.  I ran   CWBPING on the client and it came back okay.
> 
> The job log when QZDASRVSD ends:
> 
> I get this message: Which is CPE3448
> 
> 10    04/24/97   10:25:02   QZBSCOMM       QSYS        *STMT    QZBSCOMM
>   From module . . . . . . . . :   QZBSCOMM
>   From procedure  . . . . . . :   SndErrnoMsg__FPc
>   Statement . . . . . . . . . :   923
>   To module . . . . . . . . . :   QZBSCOMM
>   To procedure  . . . . . . . :   SndErrnoMsg__FPc
>   Statement . . . . . . . . . :   923
>   Message . . . . :   The protocol required to support the specified addres
>     family is not available at this time.
> 
> Then this message: Which is CPIAD08
> 
> 40    04/24/97   10:25:02   QZBSCOMM       QSYS        *STMT    QZBSCOMM
>   From module . . . . . . . . :   QZBSCOMM
>   From procedure  . . . . . . :   SndCPIAD08__FiN21
>   Statement . . . . . . . . . :   907
>   To module . . . . . . . . . :   QZBSCOMM
>  To procedure  . . . . . . . :
> SndCPIAD08__FiN21
> Statement . . . . . . . . . :   907
> Message . . . . :   HOST SERVER COMMUNICATIONS ERROR OCCURRED ON SOCKET() -
>   SPX FAMILY.
> CAUSE . . . . . :   ERROR CODE 3448 WAS RECEIVED WHILE PROCESSING THE SOCKET()
>   - SPX FAMILY FUNCTION FOR THE HOST SERVER COMMUNICATIONS. RECOVERY  . . . :
>    SEE ANY PREVIOUSLY LISTED MESSAGE(S) TO DETERMINE THE CAUSE OF THE ERROR;
>   IF NECESSARY, CORRECT THE ERROR AND ISSUE THE REQUEST AGAIN.
>     04/24/97   10:51:06   01BCE2019AB0               2030     QSOKERN3     QSY
> 
> Then the MCH3402:
> To module . . . . . . . . . :   QSODRVRS
> To procedure  . . . . . . . :   qso_open_driver__FiN31PP7qso_scbPc
> Statement . . . . . . . . . :   740
> Message . . . . :   Tried to refer to all or part of an object that no longer
>   exists.
> Cause . . . . . :   The most common cause is that a stored address to an
>   object is no longer correct because that object was deleted or part of the
> 
> Thanks for any help, still have not found a solution.

Well, as you can tell from the timestamps, the CPE3448 and CPIAD08
happened 25 minutes before the MCH3402 and are not related to your
problem.  These messages are normal (I get them all the time).
I THINK they occur if you don't have IPX protocol configured.

To confirm what your environment is:
        OS/400 V3R1M0 with PTF cum package C7044310.
        5763-XD1 V3R1M2 with Service Pack SF39220.
Have you configmed that this Service Pack is applied to the PC and not
just the AS/400 ?  

My setup is almost identical, except for being on V3R2 at PTF C7063320.
We do have a system at another office with OS/400 V3R1M1 & PTF C7044310
and they have no problems.
In both locations we are running Windows 95 connected via TCP/IP over
Ethernet.

When the MCH3402 occured there should have been a VLIC log created.  DId
you print that of via STRSST and send it in to IBM ?

A guess on the MCH3402 - it may be that one of the programs required for
file transfer is damaged/corrupted.  You may want to try reinstalling
the OS/400 Host Servers support, and 5763-XD1 V3R1M2 on the AS/400
(followed by the PTF's from the cum package again).


> 
> Original Question:
> 
> << I am attempting to install CA/95.  I am on V3R1, with current PTF tape and
> << latest Service Pack and also PTF SF38543.  I am using native Windows 95 TCP
> << Winsock 1.1 stack.  PC5250 works and I can send remote commands from the
> << client and it works.  Basically everything seems okay until I try to
> << transfer a file from the As/400 to the client.  I get a message on the
> client that
> << says  Unable to start database server.  On the As/400 the QZDASRVSD running
> in
> << QSERVER ends.
> 
> << Has anyone ran across this problem and came to a resolution ?  I've been
> << working with IBM Service for 2 days but have not come to a resolve.
> 
> I assume that since you are working with IBM, you have already made sure that
> you have run STRHOSTSVR.  What does the joblog of QZDASRVSD say?

-- 
...Neil Palmer                                      AS/400~~~~~      
...Technical Specialist             ____________          ___  ~     
...NxTrend Technology - Canada      |OOOOOOOOOO| ________  o|__||=   
...Markham, Ontario, Canada         |__________|_|______|_|______)   
...Phone: (905) 731-9000  x238       oo      oo   oo  oo   OOOo=o\   
...e-mail: neil@systemetrix.ca    ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *
* This is the Midrange System Mailing List!  To submit a new message,   *
* send your mail to "MIDRANGE-L@midrange.com".  To unsubscribe from     *
* this list send email to MAJORDOMO@midrange.com and specify            *
* 'unsubscribe MIDRANGE-L' in the body of your message.  Questions      *
* should be directed to the list owner / operator: david@midrange.com   *
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *