× The internal search function is temporarily non-functional. The current search engine is no longer viable and we are researching alternatives.
As a stop gap measure, we are using Google's custom search engine service.
If you know of an easy to use, open source, search engine ... please contact support@midrange.com.


  1.  Home
  2. LINUX5250
  3. June 2010

Re: LINUX5250 Digest, Vol 8, Issue 56

Well, let me explain what we do... when we have a printer that is physically
connected to the local PC, but not otherwise networked, and we want to use
that as an AS/400 printer, first we set it up in Windows, then we create a
"printer" terminal session. Now, it'll probably just be easier to use a
print server to print to that printer, and I just happen to have a USB
network print server. :-)



-----Original Message-----
From: linux5250-bounces@xxxxxxxxxxxx [mailto:linux5250-bounces@xxxxxxxxxxxx]
On Behalf Of Chuck Landress
Sent: Friday, June 04, 2010 1:46 PM
To: linux5250@xxxxxxxxxxxx
Subject: Re: [LINUX5250] LINUX5250 Digest, Vol 8, Issue 56

John,

Your question was a bit vague but I think you're asking about how to
establish a printer session on your PC in a way that System i Access does.
That's complicated and not neccessary. Just use Host Printer Transform.
You'll need a print spooling system running on your Linux box most
distributions use cups (Common Unix Printing Solution). Some use the older
Unix lpr (Line Printer) system. Windows has it's own spooling subsystem.

Your current printer device was probably created automatically by the System
i for you when you established your System i Access session. You'll have to
create your printer device manually.

You can specify host printer transform when you create the printer device
description (CRTDEVPRT). The System i will translate the spool output into
your printer's language. You can point the device description to your linux
machine's IP address and lpr or cups (depending on what you're running) will
handle it from there. You may have to configure lpr or cups (depending on
what you're running) to accept external input.

If you're running Windows you may be able to use Wiindows Other Network
connectivity (Windows Setup, Other Network File and Print Services)
to emulate lpr or you can get lpr software from several sources.

Here's the link to IBM's basic printing manual for V5R4:
http://publib.boulder.ibm.com/infocenter/iseries/v5r4/topic/rzalu/rzalu.pdf

-Chuck Landress


On Fri, Jun 4, 2010 at 1:00 PM, <linux5250-request@xxxxxxxxxxxx> wrote:

Send LINUX5250 mailing list submissions to
linux5250@xxxxxxxxxxxx

To subscribe or unsubscribe via the World Wide Web, visit
http://lists.midrange.com/mailman/listinfo/linux5250
or, via email, send a message with subject or body 'help' to
linux5250-request@xxxxxxxxxxxx

You can reach the person managing the list at
linux5250-owner@xxxxxxxxxxxx

When replying, please edit your Subject line so it is more specific
than "Re: Contents of LINUX5250 digest..."


*** NOTE: When replying to this digest message, PLEASE remove all text
unrelated to your reply and change the subject line so it is meaningful.

Today's Topics:

1. Re: Host-based printing in linux (Scott Klement)
2. Re: Host-based printing in linux (John Aldrich)


----------------------------------------------------------------------

message: 1
date: Thu, 03 Jun 2010 12:09:17 -0500
from: Scott Klement <tn5250@xxxxxxxxxxxxxxxx>
subject: Re: [LINUX5250] Host-based printing in linux

Hi John,

How does one set up a host-based AS/400 printer in Linux?

I'm not 100% sure that I understand your question, but... the phrase
"host-based" usually means that all of the logic of interpreting the
printout is done on the host (aka the PC) instead of on the printer
itself.

In other words, the printer manufacturer must provide a specialized
piece of software ("driver") -- one specifically designed for the exact
piece of hardware at-hand -- that interprets the printer language (PCL,
PostScript, whatever) and sends precise low-level instructions to the
printer's motors and logic boards.

Assuming you mean the same thing...

Do you have a driver like this for Linux? Did your printer
manufacturer include one?

If not, I'm afraid you're pretty much out of luck. In the future, I'd
suggest spending a few extra bucks to get a printer that's not
host-based. After all, host-based is usually the hallmark of a very
cheaply made printer.


We have several laser printers hooked up to Windows PCs that print
through Windows from the AS/400 and I'd like to replicate that in
Linux.

If the printer manufacturer provides Linux drivers, this should be easy.
Follow their instructions on how to install the driver. Make sure you
can print to it.


I know I need to get the printer set up in Linux first, but then what?
How
does one set up an AS/400 "Printer" on the local machine?

I'm not really sure... it depends on how your host-based driver takes
it's input. I've never encountered a host-based driver on Linux. I
would suspect that it would take PostScript input (since most Linux
software I've used outputs PostScript) and converts it to the printer's
low-level language. But I've never actually seen one, so this is
purely a guess.

But if I'm right, you could use a tool like scs2ps via lp5250d to print
to it...


------------------------------

message: 2
date: Thu, 3 Jun 2010 13:40:09 -0400
from: "John Aldrich" <jaldrich@xxxxxxxxxxxxxxxxxxx>
subject: Re: [LINUX5250] Host-based printing in linux

It's a Lexmark Laser printer, which is hooked up to the printer port on
the
PC, and the AS/400 sends the print job to the PC, via a dedicated terminal
session for the printer, and then prints out the job. I'll take a look at
the documentation previously referenced and see if I can get it running.
If
not, I may have to use a stand-alone print server (gee... that would be
terrible! <GRIN>)




-----Original Message-----
From: linux5250-bounces@xxxxxxxxxxxx [mailto:
linux5250-bounces@xxxxxxxxxxxx]
On Behalf Of Scott Klement
Sent: Thursday, June 03, 2010 1:09 PM
To: Linux 5250 Development Project
Subject: Re: [LINUX5250] Host-based printing in linux

Hi John,

How does one set up a host-based AS/400 printer in Linux?

I'm not 100% sure that I understand your question, but... the phrase
"host-based" usually means that all of the logic of interpreting the
printout is done on the host (aka the PC) instead of on the printer
itself.

In other words, the printer manufacturer must provide a specialized
piece of software ("driver") -- one specifically designed for the exact
piece of hardware at-hand -- that interprets the printer language (PCL,
PostScript, whatever) and sends precise low-level instructions to the
printer's motors and logic boards.

Assuming you mean the same thing...

Do you have a driver like this for Linux? Did your printer
manufacturer include one?

If not, I'm afraid you're pretty much out of luck. In the future, I'd
suggest spending a few extra bucks to get a printer that's not
host-based. After all, host-based is usually the hallmark of a very
cheaply made printer.


We have several laser printers hooked up to Windows PCs that print
through Windows from the AS/400 and I'd like to replicate that in
Linux.

If the printer manufacturer provides Linux drivers, this should be easy.
Follow their instructions on how to install the driver. Make sure you
can print to it.


I know I need to get the printer set up in Linux first, but then what?
How
does one set up an AS/400 "Printer" on the local machine?

I'm not really sure... it depends on how your host-based driver takes
it's input. I've never encountered a host-based driver on Linux. I
would suspect that it would take PostScript input (since most Linux
software I've used outputs PostScript) and converts it to the printer's
low-level language. But I've never actually seen one, so this is
purely a guess.

But if I'm right, you could use a tool like scs2ps via lp5250d to print
to it...
--
This is the Linux 5250 Development Project (LINUX5250) mailing list
To post a message email: LINUX5250@xxxxxxxxxxxx
To subscribe, unsubscribe, or change list options,
visit: http://lists.midrange.com/mailman/listinfo/linux5250
or email: LINUX5250-request@xxxxxxxxxxxx
Before posting, please take a moment to review the archives
at http://archive.midrange.com/linux5250.




------------------------------

--
This is the Linux 5250 Development Project (LINUX5250) digest list
To post a message email: LINUX5250@xxxxxxxxxxxx
To subscribe, unsubscribe, or change list options,
visit: http://lists.midrange.com/mailman/listinfo/linux5250
or email: LINUX5250-request@xxxxxxxxxxxx
Before posting, please take a moment to review the archives
at http://archive.midrange.com/linux5250.



End of LINUX5250 Digest, Vol 8, Issue 56
****************************************





As an Amazon Associate we earn from qualifying purchases.

This thread ...
Replies:
Follow On AppleNews
Return to Archive home page | Return to MIDRANGE.COM home page

This mailing list archive is Copyright 1997-2024 by midrange.com and David Gibbs as a compilation work. Use of the archive is restricted to research of a business or technical nature. Any other uses are prohibited. Full details are available on our policy page. If you have questions about this, please contact [javascript protected email address].

Operating expenses for this site are earned using the Amazon Associate program and Google Adsense.