|
Hi all, Just got back on this operation. I found that I had misnamed the temporary Domino server I installed on my AS400, so I created a new one where everything matched. It shows up on Domino administrator (sph-domino-3) and everything seems kosher. When I create the server that I want to copy my existing server to the following occurs: I copied the server.id from the NT server to the AS400 in /lotus/domino/sph-domino-1/server.id R5.05(both NT and 400) V4R5M0 The manual I am following is: Lotus Domino for AS/400 R5 Jan 2001 SG24-5592-01. Everything else is listed below. Use the address from the existing NT server like book calls for: I get Server not responding 3 times and then enter to end terminal session after the CFGDOMSVR command runs If I use an IP address that the 400 already has (instead of the NT server address), which is what the manual calls for, I get the messages below: Server not responding Server not responding Server not responding Press ENTER to end terminal session. The CFGDOMSVR command is below: CFGDOMSVR SERVER('sph-domino-1/srv/hmn') OPTION(*ADD) DTADIR('/lotus/domino/sph-domino-1') TIMEZONE(MST) NABSVR('sph-domnio-3') ADDSVRID('/lotus/domino/sph-domino-1/server.id') ADVSRV(*PARTITION) NETWORK('TCPIP Network') TCPOPT(*NOENCRYPT '206.127.80.1') SBS(DOMSPH01) The only difference between this command and when I created sph-domino-3 is the server id parameter. For server 3 I used *NAB as it is not the one I am going to copy to, just holds a copy of the NAB. Is this an authority problem, or do I have to have the existing NT Domino server shut down when I create this copy? Doug Strong Network Administrator St Peter's Hospital 2475 Broadway Helena MT 59601 (406) 444-2125 |------------------------+------------------------+------------------------| | | DStrong@stpetes.org | | | | Sent by: | To: | | | owner-domino400@midra| DOMINO400@midrange.co| | | nge.com | m | | | | cc: | | | 02/09/2001 11:00 AM | Subject: | | | Please respond to | Re: installing on | | | DOMINO400 | AS400 problems | | | | | |------------------------+------------------------+------------------------| No I did not drop sph-domino-2 (Not that I wouldn't do something like that). I created a second server on the 400 just to make sure everything was right and I kind of think the problem might lie in the fact that I am using the NT IP address to build this and that is not assigned to an interface on the 400. I will try dropping the entire NT server and then adding that interface to the 400 and see what happens. I will keep you posted, but it will not happen until next week. Thanks Doug Doug Strong Network Administrator St Peter's Hospital 2475 Broadway Helena MT 59601 (406) 444-2125 |------------------------+------------------------+------------------------| | | rob@dekko.com | | | | Sent by: | To: | | | owner-domino400@midra| DOMINO400@midrange.co| | | nge.com | m | | | | cc: | | | 02/09/2001 09:27 AM | Subject: | | | Please respond to | Re: installing on | | | DOMINO400 | AS400 problems | | | | | |------------------------+------------------------+------------------------| Isn't the NAB just names.nsf? You didn't drop the server sph-domino-2 while you were configuring -1, did you? Rob Berendt ================== Remember the Cole! DStrong@stpetes.or g To: DOMINO400@midrange.com Sent by: cc: owner-domino400@mi Subject: Re: installing on AS400 problems drange.com 02/09/01 10:32 AM Please respond to DOMINO400 Rob, Yes I can ping sph-domino-2 from the AS400 command line. What I wonder is if it really has a copy of the NAB on it I guess. Thanks Doug Doug Strong Network Administrator St Peter's Hospital 2475 Broadway Helena MT 59601 (406) 444-2125 |------------------------+------------------------+------------------------| | | rob@dekko.com | | | | Sent by: | To: | | | owner-domino400@midra| DOMINO400@midrange.co| | | nge.com | m | | | | cc: | | | 02/09/2001 06:22 AM | Subject: | | | Please respond to | Re: installing on | | | DOMINO400 | AS400 problems | | | | | |------------------------+------------------------+------------------------| Was the server 'SPH-Domino-2' communicating? Since you a creating a new server, 'SPH-Domino-1/SRV/HMN', it will try to access the NAB stored on the existing server, 'SPH-Domino-2'. I bet that 'SPH-Domino-2' is the temporary server which you've had running fine on the 400 for 3 months. And you've had seperate IP address configured for each server, right? Can you ping 'SPH-Domino-2' from your AS/400 command line? Rob Berendt ================== Remember the Cole! DStrong@stpetes.or g To: domino400@midrange.com Sent by: cc: owner-domino400@mi Subject: installing on AS400 problems drange.com 02/08/01 04:38 PM Please respond to DOMINO400 Hi all, I am in the process of trying to move my Domino from NT to the AS400. I have the brand new Lotus Domino for AS/400 R5 implementation guide. and I am doing the server transplantation process. I only have 1 server for Domino R5.05. The book said I have to have another server running and said to build a temporary server on my 400 to hold the NAB. This has been running fine for 3 months including running Trend Micros mail scan program. My AS/400 is v4r5m0 and also R5.05 Following the manual this is my config Domino Server setup; ( broke it up here for readability) CFGDOMSVR SERVER('SPH-Domino-1/SRV/HMN') OPTION(*ADD) DTADIR('/LOTUS/DOMINO/sph-domino-1') TIMEZONE(MST) NABSVR('SPH-Domino-2') ADDSVRID('/LOTUS/DOMINO/sph-domino-1/server.id' ()) DIRSRV(*NONE) CNNSRV(*NONE) ADVSRV(*PARTITION) NETWORK('TCPIP Network') TCPOPT(*NOENCRYPT '206.127.100.163') SBS(DOMSPH01) This is the message I get:: CFGDOMSVR command failed. The only thing that shows up on the domino console is: log file created /LOTUS/DOMINO/sph-domino-1/log.nsf Server not responding Server not responding I copied the log.nsf file out and opened it up and it just had the log file created message in it. The AS400 log shows the following: Ownership of object CFGDOMSVR in QUSRNOTES type *USRSPC changed. Ownership of object CFGDOMSVR in QUSRNOTES type *DTAQ changed. Object copied. Object copied. (lots of the opject copied) Object OBJS in QTEMP type *USRSPC deleted. CFGDOMSVR command failed. Any Ideas of what might be wrong or somewhere else to look for error entries? Thanks Doug ps. Thanks for all the help everyone has been for all the other questions I asked. Doug Strong Network Administrator St Peter's Hospital 2475 Broadway Helena MT 59601 (406) 444-2125 +--- | This is the Domino/400 Mailing List! | To submit a new message, send your mail to DOMINO400@midrange.com. | To subscribe to this list send email to DOMINO400-SUB@midrange.com. | To unsubscribe from this list send email to DOMINO400-UNSUB@midrange.com. | Questions should be directed to the list owner/operator: meechamw@ptd.net +--- +--- | This is the Domino/400 Mailing List! | To submit a new message, send your mail to DOMINO400@midrange.com. | To subscribe to this list send email to DOMINO400-SUB@midrange.com. | To unsubscribe from this list send email to DOMINO400-UNSUB@midrange.com. | Questions should be directed to the list owner/operator: meechamw@ptd.net +--- +--- | This is the Domino/400 Mailing List! | To submit a new message, send your mail to DOMINO400@midrange.com. | To subscribe to this list send email to DOMINO400-SUB@midrange.com. | To unsubscribe from this list send email to DOMINO400-UNSUB@midrange.com. | Questions should be directed to the list owner/operator: meechamw@ptd.net +--- +--- | This is the Domino/400 Mailing List! | To submit a new message, send your mail to DOMINO400@midrange.com. | To subscribe to this list send email to DOMINO400-SUB@midrange.com. | To unsubscribe from this list send email to DOMINO400-UNSUB@midrange.com. | Questions should be directed to the list owner/operator: meechamw@ptd.net +--- +--- | This is the Domino/400 Mailing List! | To submit a new message, send your mail to DOMINO400@midrange.com. | To subscribe to this list send email to DOMINO400-SUB@midrange.com. | To unsubscribe from this list send email to DOMINO400-UNSUB@midrange.com. | Questions should be directed to the list owner/operator: meechamw@ptd.net +--- +--- | This is the Domino/400 Mailing List! | To submit a new message, send your mail to DOMINO400@midrange.com. | To subscribe to this list send email to DOMINO400-SUB@midrange.com. | To unsubscribe from this list send email to DOMINO400-UNSUB@midrange.com. | Questions should be directed to the list owner/operator: meechamw@ptd.net +---
As an Amazon Associate we earn from qualifying purchases.
This mailing list archive is Copyright 1997-2024 by midrange.com and David Gibbs as a compilation work. Use of the archive is restricted to research of a business or technical nature. Any other uses are prohibited. Full details are available on our policy page. If you have questions about this, please contact [javascript protected email address].
Operating expenses for this site are earned using the Amazon Associate program and Google Adsense.