Re: EVF9303E error

[MWHopkins@xxxxxxxxxxxxxxx]

Thanks, That took care of it.

Matt




                      batthish@ca.ibm.c
                      om                       To:       code400-l@midrange.com
                      Sent by:                 cc:
                      code400-l-admin@m        Subject:  Re: EVF9303E error
                      idrange.com


                      11/05/2002 02:23
                      PM
                      Please respond to
                      code400-l






Hi Matt,

This type of error usually indicates that something has gone wrong in the
REXX processor in CODE Editor (the profiles and most macros are written in
REXX).
To reset things without rebooting:
1) Close the editor by selecting File->Exit, this will properly shut down
editor processes.
2) Check the task list for RXAPI.EXE, if it is still there, kill it.

You should then be able to start everything up nicely again.
Hope this helps!

Violaine Batthish
CODE Project Lead
batthish@ca.ibm.com          IBMCA(BATTHISH)


WDT/400 page:  http://www.ibm.com/software/ad/wdt400
WDT/400 Support : http://www.ibm.com/software/ad/wdt400/support




                      MWHopkins@pdpgrou
                      pinc.com                 To:
code400-l@midrange.com
                      Sent by:                 cc:
                      code400-l-admin@m        Subject:  EVF9303E error
                      idrange.com


                      11/05/2002 02:08
                      PM
                      Please respond to
                      code400-l





Has anyone received the following error when a Code Editor session is
started?

Window title <Code - EVF9303E - Error>
REXXSAA error -48 (C:\WDT400\extras\profsys.lxu) - REXX may fail.
[OK]

<Code - EVF9303E - Error>
REXXSAA error -48 (C:\WDT400\macros\profile.lx) - REXX may fail.
[OK]

Code 400 editor window opens, then:

<Code - EVF9303E - Error>
REXXSAA error -48 (C:\WDT400\extras\profsys.lxu) - REXX may fail.
[OK]

<Code - EVF9303E - Error>
REXXSAA error -48 (C:\WDT400\macros\SHL.lxl) - REXX may fail.
[OK]

<Code - EVF9303E - Error>
REXXSAA error -48 (C:\WDT400\macros\profile.lx) - REXX may fail.
[OK]


I get this every once in a while when starting the Code Editor. When the
Code Editor is displayed, the token highlighting and Extras are not
enabled.

I tried ending the Code Editor, and the Communication Daemon and
re-starting but it continues until I re-boot.

It doesn't happen all the time just periodically.

Any suggestions?

Thanks, Matt




_______________________________________________
This is the CODE/400 Discussion & Support (CODE400-L) mailing list
To post a message email: CODE400-L@midrange.com
To subscribe, unsubscribe, or change list options,
visit: http://lists.midrange.com/cgi-bin/listinfo/code400-l
or email: CODE400-L-request@midrange.com
Before posting, please take a moment to review the archives
at http://archive.midrange.com/code400-l.

NOTE: WDSc for iSeries disucssion has it's own mailing list.
Information can be found at
http://lists.midrange.com/cgi-bin/listinfo/wdsc-l




_______________________________________________
This is the CODE/400 Discussion & Support (CODE400-L) mailing list
To post a message email: CODE400-L@midrange.com
To subscribe, unsubscribe, or change list options,
visit: http://lists.midrange.com/cgi-bin/listinfo/code400-l
or email: CODE400-L-request@midrange.com
Before posting, please take a moment to review the archives
at http://archive.midrange.com/code400-l.

NOTE: WDSc for iSeries disucssion has it's own mailing list.
Information can be found at
http://lists.midrange.com/cgi-bin/listinfo/wdsc-l