RE: Working with DataArea in COBOL

["Amjad Zamil" <amjadz@xxxxxxxxxx>]

Geir,

 

 I appreciate it if you can send me an example (CL + COBOL).

 Thanks alot.

 

 Best  Regards

 

 Amjad

-----Original Message-----
From: owner-cobol400-l@midrange.com [mailto:owner-cobol400-l@midrange.com]On Behalf Of geir.kildal@entragroup.com
Sent: Tuesday, March 13, 2001 4:04 PM
To: COBOL400-L@midrange.com
Subject: RE: Working with DataArea in COBOL

Amjad.

It's quite 'normal' to use a data area to pass parameters, but the dataarea must be read by a CL-program, and that program must pass the content to the COBOL program as a parameter(or parameters).  You must know how to use parameters in a COBOL program(LINKAGE SECTION and PROCEDURE DIVISION USING ....etc etc.).  If you don't know how, you have to look it up in a manual, or I can send you an example..


Mvh.

Geir

"Amjad Zamil" <amjadz@sts.com.jo> Sent by: owner-cobol400-l@midrange.com 12.03.01 17:06 Please respond to COBOL400-L

To:        <COBOL400-L@midrange.com>         cc:                 Subject:        RE: Working with DataArea in COBOL

Geir,
 
 Thanx for your reply.Right now,I'm not using DataArea  within the COBOL code that's wun on the AS/400.I just  went
 through reading about the issue from internet resources and found  alot pointing to DataArea as a key to solve this
 problem.I can write a totally new sample COBOL program that meets  with whatever modifications/requiremetns that
 I should do to use DataArea if this's really the correct way to go  including the required CL to build and use,as well.
 
Best  Regards
 
 Amjad Zamil
-----Original Message-----
From:  owner-cobol400-l@midrange.com [mailto:owner-cobol400-l@midrange.com]On  Behalf Of geir.kildal@entragroup.com
Sent: Monday, March 12,  2001 6:35 PM
To: COBOL400-L@midrange.com
Subject: Re:  Working with DataArea in COBOL



Amjad.

First of all, I  would check to see if the COBOL-program is expecting parameters in the call.   You mention DataAreas, they are usually read in a CL-program, whitch   can call a COBOL-program.


Mvh.

Geir Kildal  
Entra Data AS

"Amjad Zamil"  <amjadz@sts.com.jo> Sent by: owner-cobol400-l@midrange.com   12.03.01 14:10 Please respond to COBOL400-L

To:         "Cobol400 Mailing List"  <COBOL400-L@midrange.com>         cc:                   Subject:        Working with DataArea in  COBOL

Hi,

 I'm totally new to  AS/400 environment.I have searched through the mailing
list archives  for
information regarding my problem but couldn't find a clear  answer.

 I have a Sun server running  Solaris 7 with SNAP-IX installed and configured
to set an  Lu6.2
connection to AS/400 server.I managed to test the connectivity with  the
AS/400 server and
it's working ok.The problem is that I have a small  cobol program that runs
on AS/400 and
I need to pass some parameters  in/out to/from it from my SNAP-IX server and
when I check
the AS/400  log,I find that the cobol program was called but get an  error
saying
"missing parameters".I think the problem is mainly related  to the way the
cobol program
is dealing with the  DataArea.

 I appreciate it if someone  can provide me with the typical way a COBOL
program should work
with the  DataArea and whatever pre-steps on the operating system level that
should  be done.

 Thanks alot in  advance.

 Best  Regards

 Amjad Zamil <  amjadz@sts.com.jo >

+---
| This is  the COBOL/400 Mailing List!
| To submit a new message, send your mail to  COBOL400-L@midrange.com.
| To subscribe to this list send email to  COBOL400-L-SUB@midrange.com.
| To unsubscribe from this list send email to  COBOL400-L-UNSUB@midrange.com.
| Questions should be directed to the list  owner/operator: david@midrange.com
+---END