RE: Shop Order Allocations

[McK King <McK.King@xxxxxxxxxxxx>]

Hello,

You might take a look at the System Parameters(SYS800) and check the MRP &
Shop Floor System Parameters. There is a place to indicate whether you will
perform Multiple Issue for LOT/LOC/CONTAINER from --Allocations or --Entered
during Inventory Posting. Have not worked with that for some time and since
it is system wide doubt it is the culprit, but worth looking at.

Good Luck,

McK King

-----Original Message-----
From: Tom Jedrzejewicz @ San Pedro [mailto:TJedrzejewicz@contessa.com]
Sent: Wednesday, October 16, 2002 1:52 PM
To: bpcs-l@midrange.com
Subject: Re: Shop Order Allocations


Thanks for the response --

Both flags are set to Yes.  I checked a backup, and both were set to
Yes well before the behavior changed.  The user has not changed, not has
their process (at least not that I can tell).

Strange.

>>> Mhamilton8685@aol.com 10/16/02 09:13AM >>>
THIS MESSAGE IS INTENDED ONLY FOR THE USE OF THE INDIVIDUAL OR ENTITY TO
WHICH IT IS ADDRESSED AND MAY CONTAIN INFORMATION THAT IS PRIVILEGED,
CONFIDENTIAL AND EXEMPT FROM DISCLOSURE UNDER APPLICABLE LAW.  If the reader
of this message is not the intended recipient, or the employee or agent
responsible for delivering the message to the intended recipient, you are
hereby notified that any dissemination, distribution, copying, downloading,
storing or forwarding of this communication is prohibited.  If you have
received this communication in error, please notify us immediately via email
and delete the message from your computer files and/or data base.  Thank
you.
--
[ Picked text/plain from multipart/alternative ]
Tom,

Check the flag in the facility master to allow facility wide backflush.
 You
could also check to see if the shop order warehouse was changed from
non-allocatable to allocatable.

Myron Hamilton
COBUS

In a message dated 10/16/2002 10:12:45 AM Central Daylight Time,
TJedrzejewicz@contessa.com writes:


> Folks --
>
> I am still a newbie, particularly with respect to shop orders.
>
> At one of our facilities the BPCS behavior changed recently -- it
began
> allocating component lots to shop orders.  This is a problem for us,
as
> we do not necessarily know the component lots until production is
> happening.  SO it turns out to be a bunch of extra work; a clerk has
to
> white out the allocations on the shop order printout, and manually
> remove the allocations before posting the production.
>
> I suspect a setting somewhere has chenged, but I am lost where to
> start.  We are on BPCS 4.0.03 with custom Y2K mods.
>
> Thanks is advance.
> Tom Jedrzejewicz
>

_______________________________________________
This is the SSA's BPCS ERP System (BPCS-L) mailing list
To post a message email: BPCS-L@midrange.com
To subscribe, unsubscribe, or change list options,
visit: http://lists.midrange.com/cgi-bin/listinfo/bpcs-l
or email: BPCS-L-request@midrange.com
Before posting, please take a moment to review the archives
at http://archive.midrange.com/bpcs-l.

_______________________________________________
This is the SSA's BPCS ERP System (BPCS-L) mailing list
To post a message email: BPCS-L@midrange.com
To subscribe, unsubscribe, or change list options,
visit: http://lists.midrange.com/cgi-bin/listinfo/bpcs-l
or email: BPCS-L-request@midrange.com
Before posting, please take a moment to review the archives
at http://archive.midrange.com/bpcs-l.