MIDRANGE dot COM Mailing List Archive



Home » MIDRANGE-L » January 2013

Re: Remote power up of System i 520



fixed

(and if they aren't there, those options, you can add them)


2013/1/2 Yvan Janssens <ik@xxxxxxxx>


http://firefox-technical-support.blogspot.be/2011/03/how-to-enable-ssl2-in-firefox.html

It is still possible, but disabled by default due to security contraints.
It is known to be broken.


2013/1/2 Jeff Crosby <jlcrosby@xxxxxxxxxxxxxxxx>

Heh. When I search from the about:config page for "ssl2" nothing shows
up.

I'm at Firefox 17.0.1. I assume that's so new that ssl2 is completely
gone.


On Mon, Dec 31, 2012 at 1:30 PM, Mike Buglass <noqnoq@xxxxxxxxxxxx>
wrote:

You could try going to the about:config page in firefox and search on
security.enable and enable ssl2.


DrFranken wrote:
You have a POWER5 server and your web browser is too new.

First try http: instead of https: to see if that works. Try an old
version of Firefox. (You can still download version 3) Or that's why
I
like Plan "B" (the serial cable.)

- Larry "DrFranken" Bolhuis

www.frankeni.com
www.iDevCloud.com
www.iInTheCloud.com


On 12/31/2012 11:30 AM, Jeff Crosby wrote:
I have a cable direct from HMC2 (192.168.3.147) to a laptop.

The IPV4 settings on the laptop are:

IP address 192.168.3.1
Subnet mask 255.255.255.0

Everything else is blank. I can ping 192.168.3.147, but cannot open
https://192.168.3.147

Firefox says: Cannot communicate securely with peer:no common
encryption
algorithms. (Error code: ssl_error_no_cypher_overlap)
Chrome says it timed out.
IE says it cannot display the webpage.

What am I missing?




On Mon, Dec 31, 2012 at 10:42 AM, DrFranken <midrange@xxxxxxxxxxxx>
wrote:

You can use either port, just set the IP address of the PC you're
going
to use appropriately for the selected port.

If it was me, I would use the OTHER port from the one I'm going to
connect to my network so that I could change that port's IP address
and
verify access to it before I disconnected.

- Larry "DrFranken" Bolhuis

www.frankeni.com
www.iDevCloud.com
www.iInTheCloud.com

On 12/31/2012 10:18 AM, Jeff Crosby wrote:
Thanks, Pete. The information says:

ETH0 (T1) 192.168.2.147
ETH1 (T2) 192.168.3.147

which are the defaults. Does this mean the ethernet cable I use
should
get
plugged into either the T1 or T2 jack in the I5?





On Sun, Dec 30, 2012 at 9:53 AM, Pete Massiello - ML <
pmassiello-ml@xxxxxxxxxxxx> wrote:

Jeff,

To find out the address of your ASMI port, on the bezel, go to
Sequence
30
(will have to be in manual mode first), and the 2 addresses are
the
HMC1
and HMC2 port respectively.

Pete

--
Pete Massiello
iTech Solutions
http://www.itechsol.com
http://www.iInTheCloud.com




-----Original Message-----
From: midrange-l-bounces@xxxxxxxxxxxx [mailto:
midrange-l-bounces@xxxxxxxxxxxx] On Behalf Of Jeff Crosby
Sent: Friday, December 28, 2012 3:04 PM
To: Midrange Systems Technical Discussion
Subject: Re: Remote power up of System i 520

Don't laugh at this idea.

2 PCs here can function as LAN Console. Each has 2 NIC cards,
with
the
2nd NIC dedicated to the LAN Console connection. There is a
single
Linksys
switch on top of the System i rack with 3 ethernet cables
attached:

1) To the T5 (I think) jack on the System i (10.10.10.1)
2) To my PC (10.10.10.2)
3) To the office manager's PC (10.10.10.3)

This is a completely isolated network. If I run an ethernet cable
from
the ASMI to that switch and can figure out the IP address of the
ASMI,
can
I just point a browser from my PC to https://xxx.xxx.xxx.xxxwhere
xxx.xxx.xxx.xxx is the IP address? And then I could RDP to my
desktop
from
home and away we go?



On Fri, Dec 28, 2012 at 2:26 PM, Kirk Goins <kirkgoins@xxxxxxxxx>
wrote:
I think this will work and says about $10K for an HMC...
Find the default AMSI/HMC port IP addresses for your system
Attach a
laptop to which ever HMC port you choose using the same IP
subnet as
the port you are attaching to Open a browser session and log in
to
AMSI Set the other HMC port to an address that is compatible with
your
local network including Gateway address Cable up that port up to
the
local network and access AMSI In there I believe you can Power Up
the
Managed System.

.



On Fri, Dec 28, 2012 at 11:18 AM, Jeff Crosby
<jlcrosby@xxxxxxxxxxxxxxxx
wrote:
Short of an HMC, is there any way to remotely power up a System
i
520?

I have LAN Console and Remote Control Panel on my desktop at
work.
Due
to
power issues last week (low voltage from utility) after a power
outage, I changed QPWRRSTIPL to 0 for no power up when power is
restored.
In a future outage that results in my power handling program
shutting
down
the system, I have no recourse to power it up other than 1)
drive
in
to work, or 2) get an HMC, correct?

I can remote from home to my work desktop, but since the System
i
is
powered off, there ain't not no Remote Control Panel.

Thanks.

--
Jeff Crosby
VP Information Systems
UniPro FoodService/Dilgard
P.O. Box 13369
Ft. Wayne, IN 46868-3369
260-422-7531
www.dilgardfoods.com


--
This is the Midrange Systems Technical Discussion (MIDRANGE-L) mailing
list
To post a message email: MIDRANGE-L@xxxxxxxxxxxx
To subscribe, unsubscribe, or change list options,
visit: http://lists.midrange.com/mailman/listinfo/midrange-l
or email: MIDRANGE-L-request@xxxxxxxxxxxx
Before posting, please take a moment to review the archives
at http://archive.midrange.com/midrange-l.




--
Jeff Crosby
VP Information Systems
UniPro FoodService/Dilgard
P.O. Box 13369
Ft. Wayne, IN 46868-3369
260-422-7531
www.dilgardfoods.com

The opinions expressed are my own and not necessarily the opinion of my
company. Unless I say so.
--
This is the Midrange Systems Technical Discussion (MIDRANGE-L) mailing
list
To post a message email: MIDRANGE-L@xxxxxxxxxxxx
To subscribe, unsubscribe, or change list options,
visit: http://lists.midrange.com/mailman/listinfo/midrange-l
or email: MIDRANGE-L-request@xxxxxxxxxxxx
Before posting, please take a moment to review the archives
at http://archive.midrange.com/midrange-l.




--

|_|0|_| Yvan Janssens
|_|_|0|
|0|0|0|









Return to Archive home page | Return to MIDRANGE.COM home page

This mailing list archive is Copyright 1997-2014 by MIDRANGE dot COM and David Gibbs as a compilation work. Use of the archive is restricted to research of a business or technical nature. Any other uses are prohibited. Full details are available here. If you have questions about this, please contact