Thanks Rob - I had forgotten about that
The viewer shows that there is no page segment
However, I just realized that my use of the position down and position
across on a landscape format page is NOT from the corner as you look at the
landscape format, but the corner from the portrait format
Hopefully, this will point me in the right direction
Alan Shore
Programmer/Analyst, Direct Response
E:AShore@xxxxxxxx
P:(631) 200-5019
C:(631) 880-8640
"If you're going through Hell, keep going" - Winston Churchill
rob@xxxxxxxxx
Sent by:
midrange-l-bounce To
s@xxxxxxxxxxxx Midrange Systems Technical
Discussion
<midrange-l@xxxxxxxxxxxx>
01/13/2011 08:51 cc
AM
Subject
Re: Was Re: creating a page segment
Please respond to now Problem with rotation of a
Midrange Systems page segment
Technical
Discussion
<midrange-l@midra
nge.com>
To see if there is a page segment you could try the spool file viewer in
iNav.
Rob Berendt
--
Group Dekko
Dept 1600
Mail to: 2505 Dekko Drive
Garrett, IN 46738
Ship to: Dock 108
6928N 400E
Kendallville, IN 46755
http://www.dekko.com
From: Alan Shore <AlanShore@xxxxxxxx>
To: Alan Shore <AlanShore@xxxxxxxx>
Cc: Midrange Systems Technical Discussion <midrange-l@xxxxxxxxxxxx>,
midrange-l-bounces@xxxxxxxxxxxx
Date: 01/13/2011 08:36 AM
Subject: Was Re: creating a page segment now Problem with rotation
of a page segment
Sent by: midrange-l-bounces@xxxxxxxxxxxx
This is the third time that I am sending this out, but for whatever
reason,
I have not seen it pop up in my own e-mail, so I don't know if it has
popped up into anyone else's e-mail either
If you see this for a third time, my apologies
Hopefully this all makes sense to someone
I have created a Page segment object in my library
When I try to use in on a particular form, the form is printed correctly
on
A4, in landscape format.
However, the page segment (logo) is printed perpendicular to the form
Looking at what I was able to glean from my google search, I would need to
use the *ROTATION parameter within the PAGESEG command in my DDS defined
print file
When i use a value of 0 for the *ROTATION parameter, the page segment
(logo) is printed perpendicular to the form
When I use one of the other values (90, 180, 270) for the *ROTATION
parameter, the page segment (logo) does NOT print at all on the form
Questions
1. The most obvious one, anyone know what I am doing wrong
2. Is there a way to see if there is a page segment in the spool file.
Using Display spool file command does NOT show the logo
We are at V5r4
Alan Shore
Programmer/Analyst, Direct Response
E:AShore@xxxxxxxx
P:(631) 200-5019
C:(631) 880-8640
"If you're going through Hell, keep going" - Winston Churchill
Alan Shore
Programmer/Analyst, Direct Response
E:AShore@xxxxxxxx
P:(631) 200-5019
C:(631) 880-8640
"If you're going through Hell, keep going" - Winston Churchill
--
This is the Midrange Systems Technical Discussion (MIDRANGE-L) mailing
list
To post a message email: MIDRANGE-L@xxxxxxxxxxxx
To subscribe, unsubscribe, or change list options,
visit:
http://lists.midrange.com/mailman/listinfo/midrange-l
or email: MIDRANGE-L-request@xxxxxxxxxxxx
Before posting, please take a moment to review the archives
at
http://archive.midrange.com/midrange-l.
--
This is the Midrange Systems Technical Discussion (MIDRANGE-L) mailing list
To post a message email: MIDRANGE-L@xxxxxxxxxxxx
To subscribe, unsubscribe, or change list options,
visit:
http://lists.midrange.com/mailman/listinfo/midrange-l
or email: MIDRANGE-L-request@xxxxxxxxxxxx
Before posting, please take a moment to review the archives
at
http://archive.midrange.com/midrange-l.
As an Amazon Associate we earn from qualifying purchases.