Re: CPF6DF2 error

Thanks for your reply Michael
The overlay was from the AFP print driver, and landscape orientation was
specified



Alan Shore
Programmer/Analyst, Direct Response
E:AShore@xxxxxxxx
P:(631) 200-5019
C:(631) 880-8640
"If you're going through Hell, keep going" - Winston Churchill



Michael Ryan
<michaelrtr@gmail
.com> To
Sent by: Midrange Systems Technical
midrange-l-bounce Discussion
s@xxxxxxxxxxxx <midrange-l@xxxxxxxxxxxx>
cc

12/03/2009 01:54 Subject
PM Re: CPF6DF2 error


Please respond to
Midrange Systems
Technical
Discussion
<midrange-l@midra
nge.com>






How did you create the overlay? If from the AFP print driver, did you
specify landscape orientation? Just a WAG.

On Thu, Dec 3, 2009 at 1:44 PM, Alan Shore <AlanShore@xxxxxxxx> wrote:

Hi guys
unfortunately, it seems that nobody else has had this problem, but I have
persevered.
I started from scratch, changing my OVRPRTF command on the LPI,CPI one
parameter at a time until I eventually arrived at the following
OVRPRTF FILE(PICKLGL) DEVTYPE(*AFPDS) PAGESIZE(8.5 +
14 *UOM) LPI(8) CPI(16.7) FRONTMGN(.7 +
1.0) PAGRTT(90) +
OUTQ(RMTIBM) SAVE(*YES)
This produced data printed on legal size paper, landscape format that
looked close to where I want the data to print

I then changed the above to include my overlay
OVRPRTF FILE(PICKLGL) DEVTYPE(*AFPDS) PAGESIZE(8.5 +
14 *UOM) LPI(8) CPI(16.7) FRONTMGN(.7 +
1.0) PAGRTT(90) FRONTOVL(AXSLIB/PICKLGL5) +
OUTQ(RMTIBM) SAVE(*YES)
which resulted in the report NOT printing, and the error messages

AFP data stream in user space not valid.
Error occurred while transforming data.
Send request failed for spooled file PICKLGL.

Obviously the culprit is the overlay. The question
What in the overlay is causing this problem, and how can it be rectified?

Again, if anyone has any ideas, help or guidance, it is always MUCH
appreciated



Alan Shore
Programmer/Analyst, Direct Response
E:AShore@xxxxxxxx
P:(631) 200-5019
C:(631) 880-8640
"If you're going through Hell, keep going" - Winston Churchill
__________________

Hi guys
I'm having a problem with attempting to print to legal size paper in
landscape mode
The result is that instead of printing the full 14 inches width, I can

only

print up to 11 inches wide no matter what I do with CPI etc on the

ovrprtf

command
Investigating the problem shows that I get the error message CPF6DF2
which translates to
AFP data stream in user space not valid.

Now I've googled CPF6DF2, and the answers I obtain don't help me to
determine the cause of this problem.

I was wondering if anyone else had encountered this message id and how

they

rectified it

As always, any help and/.or guidance is MUCH appreciated



Alan Shore
Programmer/Analyst, Direct Response
E:AShore@xxxxxxxx
P:(631) 200-5019
C:(631) 880-8640
"If you're going through Hell, keep going" - Winston Churchill
--
This is the Midrange Systems Technical Discussion (MIDRANGE-L) mailing

list

To post a message email: MIDRANGE-L@xxxxxxxxxxxx
To subscribe, unsubscribe, or change list options,
visit: http://lists.midrange.com/mailman/listinfo/midrange-l
or email: MIDRANGE-L-request@xxxxxxxxxxxx
Before posting, please take a moment to review the archives
at http://archive.midrange.com/midrange-l.

--
This is the Midrange Systems Technical Discussion (MIDRANGE-L) mailing list
To post a message email: MIDRANGE-L@xxxxxxxxxxxx
To subscribe, unsubscribe, or change list options,
visit: http://lists.midrange.com/mailman/listinfo/midrange-l
or email: MIDRANGE-L-request@xxxxxxxxxxxx
Before posting, please take a moment to review the archives
at http://archive.midrange.com/midrange-l.