Try using the LPAR attributes (x'01E0') for LPAR number.
From the MIH/MATMATR in QSYSINC:
#define _MMTR_LPAR_INFO 0x01E0 /* @AAA*/
typedef _Packed struct _MMTR_01E0_T {
char num_of_partition; /* Number of partitions */
char partition_id;
char prim_partition; /* Primary partition */
char Srvc_Partition; /* Service partition ID @D0A*/
char Firmware_Level; /* Firmware level @D0A*/
char reserved1[3];
char logical_ser_num[10]; /* Logical serial number */
char reserved2[5]; /* @C2C*/
int Cur_Partition_Shared :1; /* 0-doesn't use shared @C0A*/
/* 1-uses shared procs @C0A*/
int Lpar_Uncapped :1; /* 0-LPAR doesn't use
uncapped proc */
/* 1-LPAR uses uncapped */
/* processors @CEA*/
int reserved4 :6; /* @CEC*/
unsigned short min_processors; /* Min number of proc. */
unsigned short max_processors; /* Max number of proc. */
unsigned short cur_processors; /* Current num. or proc. */
char reserved5[2]; /* */
unsigned int cur_min_memory; /* Min mem in megabytes */
unsigned int cur_max_memory; /* Max mem in megabytes */
unsigned int cur_avail_memory; /* Available memory in meg */
char min_percentage_int_work; /* Min. percentage of inter-
active work load @02A*/
char max_percentage_int_work; /* max % of inter. work @02A*/
char cur_percentage_int_work; /* cur % of inter. work @02A*/
char reserved6; /* @C0A*/
int High_Speed_Link :1; /* 0-Does not use HSL @C0A*/
/* 1-uses HSL @C0A*/
int reserved10 :15; /* @C0A*/
int Internal_Link :1; /* 0-Does not use link @C0A*/
/* 1-uses internal link @C0A*/
int reserved12 :15; /* @C0A*/
unsigned int Min_Proc_Capacity; /* Min processing cap @C2A*/
unsigned int Max_Proc_Capacity; /* Max pro. capacity @C2A*/
unsigned int Cur_Proc_Capacity; /* Current proc. capactiy@C2A*/
unsigned int Cur_Avail_Proc_Cap_Shared; /* Current available
proc. capaciy in shared pool
@C2A*/
unsigned short Num_Phy_Proc_Shared; /* Num of physical processors
in shared pool @C2A*/
char reserved13[2]; /* Reserved @C2A*/
/* Amount of machine hypervisor memory in megabyte units */
unsigned int Mach_Hypervisor_Memory; /*@D0A*/
unsigned short Uncapped_Weight; /*@DOA*/
/* Minimum interactive capacity portion for this partition*/
unsigned short Min_Portion_Int_Work; /*@D2A*/
/* Maximum interactive capacity portion for this partition*/
unsigned short Max_Portion_Int_Work; /*@D2A*/
/* Current interactive capacity portion for this partition*/
unsigned short Cur_Portion_Int_Work; /*@D2A*/
char reserved14[4]; /* reserved @D0A,@D2C*/
} _MMTR_01E0_T; /* @AAA*/
-----Original Message-----
From: midrange-l-bounces@xxxxxxxxxxxx
[mailto:midrange-l-bounces@xxxxxxxxxxxx] On Behalf Of Bradley V. Stone
Sent: Tuesday, December 18, 2007 7:43 AM
To: Midrange Systems Technical Discussion
Subject: RE: HELP - Problems Retreiving LPAR Number 10 and Above
I'm using the logical serial number value for everything now.
I am assuming since serial number is 8, and logical serial number is 10,
that gives you a few possibilities for a number of partitions.
What I am finding odd now is a model number MMA or something like that,
instead of a number. :)
Bradley V. Stone
BVSTools - www.bvstools.com
eRPG SDK - www.erpgsdk.com
midrange.com
