× The internal search function is temporarily non-functional. The current search engine is no longer viable and we are researching alternatives.
As a stop gap measure, we are using Google's custom search engine service.
If you know of an easy to use, open source, search engine ... please contact support@midrange.com.



Pat,

Actually we have used it quite a bit... This is a ways from the main wiring
center so maybe it is reaching it's limitations in distance and this hookup
is pushing it to a problem ?

Thanks,

Chuck


-----Original Message-----
From: midrange-l-bounces@midrange.com
[mailto:midrange-l-bounces@midrange.com] On Behalf Of Pat Barber
Sent: Thursday, February 06, 2003 1:25 PM
To: Midrange Systems Technical Discussion
Subject: Re: Printer Communications Problem

I don't believe you are going to get away with twisted
pair on a "daisy chain"... It will not hold a signal
well enough for that....


Chuck Lewis wrote:
> 
> Hi Folks,
> 
> 
> 
> Went to a remote site yesterday and hooked up an IBM 4230-102. And all is
> great. It came up OK, printed fine etc. It WAS even printing this morning.
> Well a little while ago they called and said it wasn't printing. I look at
> it and it shows Vary on pending. And they said it showed READY on the LCD
> panel. So I try varying it on and off, have them hit stop and start, turn
> the thing on and off, etc. And same thing; I show Vary on pending and they
> show Ready which made NO sense. So I had them check the comm cable on the
on
> the back and the turn it off and back on. They do that and it comes up
with
> 022 Unit Address Not Received.  At least THAT makes sense from what I am
> seeing. But it gets weirder. We use twisted pair cabling. Well in this
> office they only had 2 drops. And they had two terminals. So I did the old
> "daisy chain" deal with one of the terminals. The Cat 5 patch cable comes
> out of the wall jack and into the Balun in the twin-ax connector on the
> printer. Then out of the other side of the twin-ax connector there is
> another Balun and Cat 5 patch cable going to a Terminal. And the terminal
IS
> WORKING FINE.
> 
> 
> 
> Any ideas what might be going on ?
> 
> 
> 
> 
> 
> Chuck
> 
> 
> 
> _______________________________________________
> This is the Midrange Systems Technical Discussion (MIDRANGE-L) mailing
list
> To post a message email: MIDRANGE-L@midrange.com
> To subscribe, unsubscribe, or change list options,
> visit: http://lists.midrange.com/mailman/listinfo/midrange-l
> or email: MIDRANGE-L-request@midrange.com
> Before posting, please take a moment to review the archives
> at http://archive.midrange.com/midrange-l.
_______________________________________________
This is the Midrange Systems Technical Discussion (MIDRANGE-L) mailing list
To post a message email: MIDRANGE-L@midrange.com
To subscribe, unsubscribe, or change list options,
visit: http://lists.midrange.com/mailman/listinfo/midrange-l
or email: MIDRANGE-L-request@midrange.com
Before posting, please take a moment to review the archives
at http://archive.midrange.com/midrange-l.




As an Amazon Associate we earn from qualifying purchases.

This thread ...

Replies:

Follow On AppleNews
Return to Archive home page | Return to MIDRANGE.COM home page

This mailing list archive is Copyright 1997-2024 by midrange.com and David Gibbs as a compilation work. Use of the archive is restricted to research of a business or technical nature. Any other uses are prohibited. Full details are available on our policy page. If you have questions about this, please contact [javascript protected email address].

Operating expenses for this site are earned using the Amazon Associate program and Google Adsense.