|
At 11:02 AM 12/22/98 -0500, you wrote: > >OK, since their not in the ops guide anymore and spread all over the >manuals...provided that you have them...the SRC's can be a bit hard to >find... BUT, alas, they DO exist on the sys...can anyone tell me where? >I know they're available via SST but it's a bit clumsy to get to them and >I'm looking to write a quickie report listing them for reference....and >no, I've not had the time to rip into the SST routines..... > AS/400 Service Functions V4R2 IPL Status SRCs 6.4.2 IPL Status SRCs As the system performs an IPL, SRCs appear on the control panel. The SRCs indicate the status of the IPL and are often useful in problem analysis. The following list provides information on the IPL process and shows some SRCs (in numeric order) that can appear during an IPL. In SRCs of the following formats: C1yx xxxx, C3yx xxxx, or A1yx xxxx, y indicates that a 'special' IPL is in progress and can have one of the following values: y = 'B', 'C', 'D', or 'F': B = CPM Recovery IPL (pre-dump) C = CPM Recovery IPL (post-dump) D = Main Store Dump in progress F = MFIOP Reset/Reload in progress IPL SRC Function Performed C1yx 1xxx Service Processor ROS IPL in progress C1yx 1006 Service processor ROS loading RAM from MFIOP directed device C1yx 1007 Service Processor ROS retrying attempt to load RAM from MFIOP directed device C1yx 1008 Service Processor ROS attempting to load RAM from non-MFIOP directed device C1yx 1009 Service Processor ROS retrying attempt to load RAM from non-MFIOP directed device C1yx 1016 Service Processor ROS attempting to load RAM from MFIOP default device C1yx 1018 Service Processor ROS attempting to load RAM from non-MFIOP default device C1yx 1019 Service Processor ROS retrying attempt to load RAM from non-MFIOP default device C1yx 100C Service processor ROS IPL complete, branch to RAM Loader C1yx 1030 Loading Service Processor system LIC from MFIOP device C1yx 1050 Loading Service Processor system LIC from non-MFIOP device C1yx 2001 Service Processor is setting up to test and load system processor C1yx 2002 Service processor is testing system processor and main storage C1yx 2003 Service processor is loading system processor C100 2034 LIC (system) has been initialized; control has passed to system processor C1yx 2050 Service Processor is waiting for Load Source device C1yx 2060 Service Processor started a read command from Load Source C1yx 2090 Service Processor completed a read command from load source C1yx 80xx Service Processor/Control Panel communication in progress C1yx 805x Service Processor is loading Control Panel LIC C1yx B1xx Basic assurance test completed on MFIOP C100 D009 LIC (system) running initialization C3yx xxxx System Processor or Main Storage Diagnostic in progress C5yx xxxx LIC system hardware initialization C500 C92B Waiting for console device - error condition only if console not found C6xx 1800 LIC SPCN setup C600 4001 Static paging C600 4002 Start limited paging, call LID manager C600 4003 Initialize IPL/Termination (IT) data area / set up node address communication area (NACA) pointer C600 4004 Check and update MSD SID C600 4005 Initialize event management is running C600 4006 IPL all buses C600 4007 Start error log ID C600 4008 Initialize I/O service C600 4009 Initialize I/O machine C600 4010 Initialize IDE (interactive device exerciser) C600 4011 Initialize remote services C600 4012 Initialize RMAC component data values C600 4013 Initialize context management C600 4014 Initialize RM (component) seize lock C600 4015 Initialize MISR C600 4016 Set time of day C600 4017 Initialize RM (component) process management C600 4018 Initialize error log C600 4019 Restart the service processor C600 4020 Initialize machine services C600 4021 Initialize performance data collector C600 4022 Initialize event management C600 4023 Create MI boundary manager tasks C600 4024 Disable CPM C600 4025 Initializes battery test C600 4026 Hardware card checkout C600 4027 Start integrated device exerciser (Type C IPL only) C600 4028 Start DST C600 4029 Make IPL task not critical C600 4030 Free static storage C600 4031 Destroy IPL task C600 4050 Storage management recovery is running C600 4051 Start LOG is running C600 4052 Trace table initialization is running C600 4053 Context rebuild is running C600 4054 Start product activity log and Advanced Peer-to-Peer Networking (APPN) is running C600 4055 Authority recovery is running C600 4056 Journal recovery is running C600 4057 Database recovery is running C600 4058 Journal synchronization is running C600 4059 Commit recovery is running C600 4060 Database initialization is running C600 4061 Journal IPL clean up is running C600 4062 Commit initialization is running C600 4064 System Object Model (SOM) recovery is running C600 4065 Start operating system is running C600 4101 Opening media-file to install LIC service displays with proper National Language Version C600 4102 Loading and linking from media-file to install LIC service displays with proper National Language Version C600 4201 Storage management recovery C600 4204 Synchronization of mirrored MSD C6xx 4205 Synchronization of mirrored data (where xx is percent complete). C600 4240 Reclaim main storage C600 4250 Storage management subset directory recovery C600 4255 Defragmentation utility C600 4260 Storage management directory recovery C600 4272 ASP overflow recovery C600 4300 Static paging is available for the link loader C600 4301 Applying temporary PTFs. If the IPL stops at this point, you might need to install the Licensed Internal Code again. C600 4302 Applying modules. If the IPL stops at this point, you might need to install the Licensed Internal Code might again. C600 4303 Temporarily applied PTFs have reached the static paging phase C600 432A Resolving references to run Mode A; you can safely stop the system while it is doing this work. C600 432B Resolving references to run Mode B. You may safely stop the system while it is doing this work. C600 4330 Full paging is available; workstation HRI processing C600 4331 Freeing unused nucleus pages C600 4332 Permanently applying PTFs. If the IPL stops at this point, you may need to install the Licensed Internal Code again. The following SRCs can appear during an MSD IPL. C6xx 4400 Unattended DASD checker started C6xx 4401 Attended DASD checker started C600 4402 Main storage dump manager and storage management recovery started C600 4403 Storage management recovery ended C6xx 4404 LIC log started (where xx is dump copy percent completed). C600 4405 Dump auto copy completed. Shutdown or programmed IPL has started. C600 4406 Shutdown or programmed IPL (MSD related) has started. End of MSD IPL SRCs. The following SRCs can appear during a CPM IPL. C6xx 4410 Unattended DASD checker started C6xx 4411 Attended DASD checker started C600 4412 Storage management recovery started C600 4414 LIC log started C600 4416 Shutdown or programmed (CPM-related) IPL has started End of CPM IPL SRCs. The following are DST SRCs for Attended IPLs. C600 4500 Verifying network attributes C600 4501 Looking for the console C600 4502 Starting DST display task C600 4503 Checking possible machine-readable information (MRI) on media C600 4504 Verifying system serial number C600 4505 Verifying system type C600 4506 Verifying system-unique ID (OS/400 only) C600 4507 Starting 'before DST' DASD checker C600 4508 Verifying system password (if DASD check OK; if not OK this is checked when IPL'ing past DST) C600 4509 Starting DASD migration function (only if migrating) C600 450A Starting 'after DST' DASD checker (can happen twice) The following are DST SRCs for Unattended IPLs. C600 4500 Verifying network attributes C600 4502 Starting DST display task (SSP only) C600 4503 Checking possible MRI on media (SSP only) C600 4504 Verifying system serial number C600 4505 Verifying system type C600 4506 Verifying system-unique ID (OS/400 only) C600 4508 Verifying system password (if DASD check OK) C600 450A Starting 'after DST' DASD checker End of DST SRCs for Unattended IPLs. C600 4A57 Parallel database recovery is at Pass 1 C600 4A60 Parallel database initialization is at Pass 1 C600 4B57 Parallel database recovery is at Pass 2 C600 4B60 Parallel database initialization is at Pass 2 C600 4C57 Parallel database recovery is at Pass 3 C600 4C60 Parallel database initialization is at Pass 3 C600 4F57 The system is recovering all database objects. This step can take several hours. It can occur any time when database recovery is in progress. C600 4F60 The system is examining all objects during database initialization. It can occur any time when database initialization is in progress. Note: At this point LIC initialization is complete, and operating system starts. All hardware is verified. IPL SRC Function Performed If the system uses the OS/400 operating system, the following status SRCs appear: C900 2810 Reclaim machine context C900 2820 Resolve system objects C900 2825 Convert Work Control Block Table C900 2830 System value object C900 28C0 Prepare SPCF job C900 28C5 Initialize system objects C900 2910 Start system logging C900 2920 Library and object information repository (OIR) cleanup C900 2925 Verify POSIX** root directories C900 2930 Database cross-reference C900 2940 Console configuration C900 2950 Install complex objects C900 2960 Sign on processing C900 2965 Software Management Services (SMS) initialization C900 2967 Applying PTFs C900 2968 IPL options C900 2970 Database recovery part 1, journal recovery part 1 C900 2980 Storage requirements C900 2990 Performance adjustments C900 29A0 System control block C900 29B0 Spool initialization C900 29C0 Work control block table C900 2A80 Before starting system jobs C900 2A85 Bringing up POSIX SAG C900 2A87 POSIX SAG restart and signals initialization C900 2A90 Starting system jobs C900 2A95 Abnormal Work Control Block Table cleanup C900 2AA0 Damage Notification C900 2AA5 Integrated File System/New File System (NFS) directory recovery C900 2AB0 Database Recovery part 2 C900 2AC0 Document Library Object (DLO) recovery C900 2B10 Establish event monitors C900 2B30 QLUS job C900 2B40 Device configuration C900 2C10 After system arbiter C900 2C20 SNADS recovery C900 2C25 ZMF component (Mail Enablement (OeDS) Framework) recovery C900 2C40 Work Control Block Table cleanup C900 2F00 IPL Complete If the system uses the SSP operating system, the following status SRCs appear: CA00 0100 Start SSP operating system Operating system initialization is complete when the sign-on screen displays on the console. Anything else I can do for ya??? Al +--------------------------------------------------+ | Please do not send private mail to this address. | | Private mail should go to barsa@ibm.net. | +--------------------------------------------------+ Al Barsa, Jr. - Account for Midrange-L Barsa Consulting, LLC. 400 > 390 Phone: 914-251-1234 Fax: 914-251-9406 http://www.barsaconsulting.com +--- | This is the Midrange System Mailing List! | To submit a new message, send your mail to MIDRANGE-L@midrange.com. | To subscribe to this list send email to MIDRANGE-L-SUB@midrange.com. | To unsubscribe from this list send email to MIDRANGE-L-UNSUB@midrange.com. | Questions should be directed to the list owner/operator: david@midrange.com +---
As an Amazon Associate we earn from qualifying purchases.
This mailing list archive is Copyright 1997-2024 by midrange.com and David Gibbs as a compilation work. Use of the archive is restricted to research of a business or technical nature. Any other uses are prohibited. Full details are available on our policy page. If you have questions about this, please contact [javascript protected email address].
Operating expenses for this site are earned using the Amazon Associate program and Google Adsense.