× The internal search function is temporarily non-functional. The current search engine is no longer viable and we are researching alternatives.
As a stop gap measure, we are using Google's custom search engine service.
If you know of an easy to use, open source, search engine ... please contact support@midrange.com.



Mike, the seu message knows nothing about the file at this point, its the point of entry when I press enter that the message pops up.



Joe Pluta may be right, its just not acceptable to use *Start/*End with SETGT.

I understand its not feasible to list all outcomes that's not appropriate but I feel this should have been an exception, I could have lost a paycheck on this one!



You can replace with SETLL, or if your not concern with the nulls then use *Hival/*Loval along with SETGT.



I just didn't see that one coming. Still, I feel there's something im not seeing here.





JoeM


----- Original Message ----- From: "Mike Cunningham" <mcunning@xxxxxxx>
To: "'RPG programming on the AS400 / iSeries'" <rpg400-l@xxxxxxxxxxxx>
Sent: Wednesday, December 05, 2007 6:01 PM
Subject: RE: SETGT *End/*Start


Are you files keyed logicals ?

On SETLL *LOVAL repositions at the start of a keyed file *START repositions at the start of a non-keyed file
On SETGT *HIVAL repositions at the end of a keyed file *END repositions at the end of a non-keyed file

-----Original Message-----
From: rpg400-l-bounces@xxxxxxxxxxxx [mailto:rpg400-l-bounces@xxxxxxxxxxxx] On Behalf Of OPLink
Sent: Wednesday, December 05, 2007 7:16 PM
To: RPG programming on the AS400 / iSeries
Subject: SETGT *End/*Start


We are on 5.3 and I can not use the *END or *START
with SETGT as shown below. In SEU the error message
RNF5318 pops up when enter is pressed. I can not find any
docs on the cause of error or that I can even use the *START/*END
with SETGT. However, they both work fine for SETLL.

Am I missing a PTF??

thanks
JoeM
-----------------------------------

C *START SETGT ITEMBL

Factor 1 entry has a data type that is not allowed for this operation; speci...


-----------------------------------
F1 on message line
-----------------------------------
Additional Message Information

Message ID . . . . . . : RNF5318 Severity . . . . . . . : 30
Message type . . . . . : Diagnostic

Message . . . . : Factor 1 entry has a data type that is not allowed for
this operation; specification is ignored.
Cause . . . . . : The Factor 1 entry (positions 12 - 25) must have the
correct data type.
Recovery . . . : Correct the Factor 1 entry (positions 12 - 25). Compile
again.
--
This is the RPG programming on the AS400 / iSeries (RPG400-L) mailing list
To post a message email: RPG400-L@xxxxxxxxxxxx
To subscribe, unsubscribe, or change list options,
visit: http://lists.midrange.com/mailman/listinfo/rpg400-l
or email: RPG400-L-request@xxxxxxxxxxxx
Before posting, please take a moment to review the archives
at http://archive.midrange.com/rpg400-l.


--
This is the RPG programming on the AS400 / iSeries (RPG400-L) mailing list
To post a message email: RPG400-L@xxxxxxxxxxxx
To subscribe, unsubscribe, or change list options,
visit: http://lists.midrange.com/mailman/listinfo/rpg400-l
or email: RPG400-L-request@xxxxxxxxxxxx
Before posting, please take a moment to review the archives
at http://archive.midrange.com/rpg400-l.



As an Amazon Associate we earn from qualifying purchases.

This thread ...

Follow-Ups:
Replies:

Follow On AppleNews
Return to Archive home page | Return to MIDRANGE.COM home page

This mailing list archive is Copyright 1997-2024 by midrange.com and David Gibbs as a compilation work. Use of the archive is restricted to research of a business or technical nature. Any other uses are prohibited. Full details are available on our policy page. If you have questions about this, please contact [javascript protected email address].

Operating expenses for this site are earned using the Amazon Associate program and Google Adsense.