× The internal search function is temporarily non-functional. The current search engine is no longer viable and we are researching alternatives.
As a stop gap measure, we are using Google's custom search engine service.
If you know of an easy to use, open source, search engine ... please contact support@midrange.com.



Thanks for the reply Paul. We don't want to initialize the tapes, as
the tapes contain active data and the data is critical.

On Fri, Apr 25, 2014 at 9:27 PM, Steinmetz, Paul <PSteinmetz@xxxxxxxxxx> wrote:
I've had volumes with in BRMS go into an error status.
When this happens the BRMS volume id some is changed and does not match the physical id.
All of my errors where of the logical type, none were ever physically damaged.
BRMS has a fix that I've used successfully.

Reasons Why a BRMS-Enrolled Volume Will Be Marked in *ERR

http://www-01.ibm.com/support/docview.wss?uid=nas8N1015143


On some of these errors, if the volume ID is not posted in the message, BRMS cannot mark the volume in error.

Notes:
1. After a volume is marked in *ERR, it can be reset only by removing the volume, then adding the volume back into the BRMS inventory by using the ADDMLMBRM command. Normally, the volume can be initialized and reused. However, if it continues to be marked in error, the volume should be discarded and replaced.
2. If an active volume is marked in *ERR, an attempt to remove it will fail with:

BRM1491 - Message . . . . : Volume 284AAO not removed.
Cause . . . . . : Volume 284AAO cannot be removed because it contains active data.
The volume contents must be expired before the volume can be removed.
Caution: Expiring a volume manually with option 7=Expire in WRKMEDBRM will delete the associated media information.
3. Volumes with active data on them may still be used to restore from while in *ERR; however if they have expired, the actions in Note 1 must be followed.
4. At 7.1 the *ERR status can be removed by using option 9=Remove volume error status in WRKMEDBRM.


-----Original Message-----
From: midrange-l-bounces@xxxxxxxxxxxx [mailto:midrange-l-bounces@xxxxxxxxxxxx] On Behalf Of Ankush Agrawal
Sent: Friday, April 25, 2014 11:35 AM
To: Midrange Systems Technical Discussion
Subject: BRMS Tape labels

Hi All,

Is there any way we can change the labels of tape.

Issue : There are few active tapes which didn't had labels. We labelled them and added to BRMS inventory. When we did DSPTAP, the
external label and internal label were different. But the tapes are
in *ERR status. is there any way we can change the labels and make both the labels same.

Thanks
--
This is the Midrange Systems Technical Discussion (MIDRANGE-L) mailing list To post a message email: MIDRANGE-L@xxxxxxxxxxxx To subscribe, unsubscribe, or change list options,
visit: http://lists.midrange.com/mailman/listinfo/midrange-l
or email: MIDRANGE-L-request@xxxxxxxxxxxx Before posting, please take a moment to review the archives at http://archive.midrange.com/midrange-l.

--
This is the Midrange Systems Technical Discussion (MIDRANGE-L) mailing list
To post a message email: MIDRANGE-L@xxxxxxxxxxxx
To subscribe, unsubscribe, or change list options,
visit: http://lists.midrange.com/mailman/listinfo/midrange-l
or email: MIDRANGE-L-request@xxxxxxxxxxxx
Before posting, please take a moment to review the archives
at http://archive.midrange.com/midrange-l.


As an Amazon Associate we earn from qualifying purchases.

This thread ...

Follow-Ups:
Replies:

Follow On AppleNews
Return to Archive home page | Return to MIDRANGE.COM home page

This mailing list archive is Copyright 1997-2024 by midrange.com and David Gibbs as a compilation work. Use of the archive is restricted to research of a business or technical nature. Any other uses are prohibited. Full details are available on our policy page. If you have questions about this, please contact [javascript protected email address].

Operating expenses for this site are earned using the Amazon Associate program and Google Adsense.