Re: Migrate twinax console to LAN console V5R2

This is a 9406-810 that a BP will be setting up. Was HMC even available back then?

Scott

________________________________________
From:midrange-l-bounces@xxxxxxxxxxxx [midrange-l-bounces@xxxxxxxxxxxx] on behalf of Jack Kingsley [iseriesflorida@xxxxxxxxx]
Sent: Monday, July 02, 2012 1:25 PM
To: Midrange Systems Technical Discussion
Subject: Re: Migrate twinax console to LAN console V5R2

Scott, you haven't mentioned hmc, are you using VPM(virtual partition
manager) via SST to create your LPAR's using twinax.

On Mon, Jul 2, 2012 at 2:14 PM, Jim Oberholtzer<midrangel@xxxxxxxxxxxxxxxxx

> wrote:
> The procedure in the V5R4 Info center is essentially the same as it was
> in V5R2, difference being some of the options for setting up the console
> device and the user. You may have to hunt/peck for those. Also, I
> don't remember exactly but there was a change where you could get to
> those functions with SST, at V5R2 they may only be available from DST.
> I would try a function 21 to see if the DST presented that way will give
> you the options, otherwise you may have to IPL into DST to set it up.
>
> Jim Oberholtzer
> Chief Technical Architect
> Agile Technology Architects
>
>
> On 7/2/2012 12:56 PM, Lindstrom, Scott R. wrote:

> > Unfortunately that link is for:
> >
> > Software version:
> > 5.4.5, 6.1, 6.1.1,
> > V5R4M0, V5R4M5, V6R1M0, V6R1M1
> >
> > I am V5R2.
> >
> > ________________________________________
> > From:midrange-l-bounces@xxxxxxxxxxxx [midrange-l-bounces@xxxxxxxxxxxx]

> on behalf of Jim Oberholtzer [midrangel@xxxxxxxxxxxxxxxxx]

> > Sent: Monday, July 02, 2012 11:36 AM
> > To: Midrange Systems Technical Discussion
> > Subject: Re: Migrate twinax console to LAN console V5R2
> >
> > That option was not added until V5R4 I think. You need to use the front
> > panel (65+21) to change the console. I think the link sent earlier has
> > the exact instructions.
> >
> > Jim Oberholtzer
> > Chief Technical Architect
> > Agile Technology Architects
> >
> >
> > On 7/2/2012 11:28 AM, Lindstrom, Scott R. wrote:

> >> > Jack - this is opt 8 in V5R2:
> >> >
> >> > 8. Work with service tools user IDs
> >> >
> >> > Which brings me here:
> >> >
> >> > Work with Service Tools User IDs
> >> > System:
> >> > pe option, press Enter.
> >> > 1=Create 2=Change password 3=Delete
> >> > 4=Display 5=Enable 6=Disable
> >> > 7=Change privileges 8=Change description
> >> >
> >> > There is no option to set the console type. Is it somewhere else in

> V5R2?

> >> >
> >> > Scott
> >> >
> >> >
> >> > -----Original Message-----
> >> > From:midrange-l-bounces@xxxxxxxxxxxx [mailto:

> midrange-l-bounces@xxxxxxxxxxxx] On Behalf Of Jack Kingsley

> >> > Sent: Monday, July 02, 2012 11:25 AM
> >> > To: Midrange Systems Technical Discussion
> >> > Subject: Re: Migrate twinax console to LAN console V5R2
> >> >
> >> > start SST, take opiton 8 (Work with service tools user IDs and

> Devices),

> >> > can you do anything with option 3 that would allow you to change it

> to lan

> >> > console.
> >> >
> >> >
> >> >
> >> > On Mon, Jul 2, 2012 at 12:17 PM, Lindstrom, Scott R.<
> >> > Scott.Lindstrom@xxxxxxxxxxxxxx> wrote:
> >> >

> >>>> >> > Sorry - that link was valid before. It is a PDF document

> that gives the

> >>>> >> > steps to do this V5R4M5 and beyond.
> >>>> >> >
> >>>> >> > Scott
> >>>> >> >
> >>>> >> >
> >>>> >> > -----Original Message-----
> >>>> >> > From:midrange-l-bounces@xxxxxxxxxxxx [mailto:
> >>>> >> > midrange-l-bounces@xxxxxxxxxxxx] On Behalf Of Lindstrom,

> Scott R.

> >>>> >> > Sent: Monday, July 02, 2012 11:16 AM
> >>>> >> > To:MIDRANGE-L@xxxxxxxxxxxx
> >>>> >> > Subject: Migrate twinax console to LAN console V5R2
> >>>> >> >
> >>>> >> > I have a V5R2 system that I need to get over to LAN console

> so we can add

> >>>> >> > some LPAR's. I found this document:
> >>>> >> >
> >>>> >> >
> >>>> >> >

> http://www-01.ibm.com/support/docview.wss?uid=nas179a308457dd4c6c18625770e0057530f

> >>>> >> >
> >>>> >> > But it covers V5R4M5 and beyond; it directs you into SST

> option 8 "user

> >>>> >> > IDs and*devices*" to set the console type to '3' Ops

> Console. In V5R2 the

> >>>> >> > 'devices' part is not there.
> >>>> >> >
> >>>> >> > Does anyone know how I change the console type from Twinax

> to Ops LAN

> >>>> >> > console in V5R2?
> >>>> >> >
> >>>> >> > Scott Lindstrom
> >>>> >> >
> >>>> >> > --

> > --