× The internal search function is temporarily non-functional. The current search engine is no longer viable and we are researching alternatives.
As a stop gap measure, we are using Google's custom search engine service.
If you know of an easy to use, open source, search engine ... please contact support@midrange.com.



Hi Chris,
I took your advise on this issue, but it seems to be timing out on the
physical HMC.
I went to the Physical HMC. Logged on using a shared session.
I came back to my desk and opened a shared session

Checked it a couple of hours later and I'm back to a signon screen.

I'm wondering if this is happening because of the QINACTITV system
value?


-----Original Message-----
From: midrange-l-bounces@xxxxxxxxxxxx
[mailto:midrange-l-bounces@xxxxxxxxxxxx] On Behalf Of Chris Bipes
Sent: Wednesday, March 30, 2011 10:36 AM
To: Midrange Systems Technical Discussion
Subject: RE: New to HMC- having timeout issue

One way would be to have someone log on to the HMC locally. Have them
open shared Console session. Then you connect remotely using a Shared
session and the password they setup for you locally. Then if your
session times out due to inactivity or communications failure, the
console is still connected. You can reconnect and be at the same place.

However this means your remote HMC is logged on all the time and the
shared console is available at the remote location as well as your local
session. They share and see the same screens. I do this as our HMC is
in a secure location, in the same rack as our iSeries. When all else
fails, I can use the remote KVM to open the HMC as if I was at its
keyboard.

--
Chris Bipes
Director of Information Services
CrossCheck, Inc.

-----Original Message-----
From: midrange-l-bounces@xxxxxxxxxxxx
[mailto:midrange-l-bounces@xxxxxxxxxxxx] On Behalf Of Smith, Mike
Sent: Wednesday, March 30, 2011 6:10 AM
To: Midrange Systems Technical Discussion
Subject: New to HMC- having timeout issue

We just upgraded to a Power 7 box a week ago, so this is our first
exposure to using a HMC. Previously we had a twinax attached Console.


We are running V7R7.2.0.1 of HMC. The HMC is located offsite.

Now the problem I'm having is that I create a 5250 session to the
console, but it will timeout after about 90 minutes with the following
messages.

CPF5140 Session stopped by a request from device DSP01.
CPF2677 Device DSP01 no longer communicating

This is not terrible except that we use a custom System Save. The
system save is started on DSP01 and waits until a message is sent from
the job scheduler to start the save. We can't get this to work now
because of the timeout. How can I prevent the Console from timing out?

I guess as a side question, Is it still a requirement that the system
save run from a Console?

--
This is the Midrange Systems Technical Discussion (MIDRANGE-L) mailing
list To post a message email: MIDRANGE-L@xxxxxxxxxxxx To subscribe,
unsubscribe, or change list options,
visit: http://lists.midrange.com/mailman/listinfo/midrange-l
or email: MIDRANGE-L-request@xxxxxxxxxxxx Before posting, please take a
moment to review the archives at http://archive.midrange.com/midrange-l.




NOTICE: This message, including any attachment, is intended as a confidential and privileged communication. If you have received this message in error, or are not the named recipient(s), please immediately notify the sender and delete this message.

As an Amazon Associate we earn from qualifying purchases.

This thread ...

Follow-Ups:

Follow On AppleNews
Return to Archive home page | Return to MIDRANGE.COM home page

This mailing list archive is Copyright 1997-2024 by midrange.com and David Gibbs as a compilation work. Use of the archive is restricted to research of a business or technical nature. Any other uses are prohibited. Full details are available on our policy page. If you have questions about this, please contact [javascript protected email address].

Operating expenses for this site are earned using the Amazon Associate program and Google Adsense.