× The internal search function is temporarily non-functional. The current search engine is no longer viable and we are researching alternatives.
As a stop gap measure, we are using Google's custom search engine service.
If you know of an easy to use, open source, search engine ... please contact support@midrange.com.



I can confirm this. Happens on older 520, 520+, 515, and 525. Must have
something to do with the FSP which probably talks to the UPS, not i5/OS
directly.

That's why my procedure described the whole power down/unplug work.

-----Original Message-----
From: midrange-l-bounces@xxxxxxxxxxxx
[mailto:midrange-l-bounces@xxxxxxxxxxxx] On Behalf Of
ChadB@xxxxxxxxxxxxxxxxxxxx
Sent: Tuesday, September 04, 2007 10:32 PM
To: Midrange Systems Technical Discussion
Subject: Re: UPS Connection at V5R4


There are (or were at some V5R3 PTF levels) situations where the 520s
will not see the cable being attached/detached unless it was detected at
power up of the box (and on some occasions, we had to actually UNPLUG
the 520).
Don't remember all the details as it's been almost 3 years ago, but
there were definitely some hoops to jump through with these UPS cables.





James Lampert

<jamesl@touchtone

corp.com>
To
Sent by: Midrange Systems Technical

midrange-l-bounce Discussion

s@xxxxxxxxxxxx <midrange-l@xxxxxxxxxxxx>


cc


09/04/2007 04:10
Subject
PM Re: UPS Connection at V5R4





Please respond to

Midrange Systems

Technical

Discussion

<midrange-l@midra

nge.com>









Lukas Beeler wrote:
The only way i found so far to test this was very very stupid (there
probably is a better one):

Power down the machine. Unplug the power (to power down the FSP).
Unplug the UPS cable. Power up the machine. You might now see a
message telling you that an UPS has been disconnected. Power down the
machine. Unplug the Power. Plugin the UPS cable. Power up the machine.

Check DSPLOG and QSYSOPR MSGQ for a message telling you that an UPS
was found.

There should be no need to power down the machine to test whether or not
it can detect connection/disconnection of the UPS cable. We've
connected/disconnected these cables on "live" machines with no problems
whatsoever.

We've even had (and it's in the archives) to add relay boxes to suppress
the "low battery" signal during UPS self-tests, as that signal, combined
with an "on battery power" signal, induces an immediate, unstoppable,
emergency power-down (with the consequence of a rather protracted IPL).
We've also constructed relay boxes to mimic UPS signals purely based on
line power status.

With a chart of the pinouts, and the appropriate breakout box, it should
be possible to simulate any possible combination of UPS signals (but
again, note that some will initiate an emergency power-down, leaving a
large mess to be cleaned up during the next IPL).

--
James H. H. Lampert
Touchtone Corporation

--
This is the Midrange Systems Technical Discussion (MIDRANGE-L) mailing
list To post a message email: MIDRANGE-L@xxxxxxxxxxxx To subscribe,
unsubscribe, or change list options,
visit: http://lists.midrange.com/mailman/listinfo/midrange-l
or email: MIDRANGE-L-request@xxxxxxxxxxxx Before posting, please take a
moment to review the archives at http://archive.midrange.com/midrange-l.



As an Amazon Associate we earn from qualifying purchases.

This thread ...

Follow-Ups:
Replies:

Follow On AppleNews
Return to Archive home page | Return to MIDRANGE.COM home page

This mailing list archive is Copyright 1997-2024 by midrange.com and David Gibbs as a compilation work. Use of the archive is restricted to research of a business or technical nature. Any other uses are prohibited. Full details are available on our policy page. If you have questions about this, please contact [javascript protected email address].

Operating expenses for this site are earned using the Amazon Associate program and Google Adsense.