question about brms network backups -- MIDRANGE-L

 Steve,

Thanks so much for your response, and no we are not using a data
mirroring package.  

I am going to try to explain the scenario more clearly, keep in mind, we
are relatively new and self-taught, self-trained, on the iSeries, but
between the  4 people in my group, we each have at least 20 years
experience in IT each (now that I think of it - I think we may almost
have 100 years collectively).

Here goes - We have iSeries Production machine (A) at our location.
This is a 680 GB machine that we use 60-70% of the disk space regularly.
We have a disaster recovery/backup machine (B) that is 215 GB and that
is located 50 miles away.  Attached to B is a tape drive.  We would like
to have machine B (the remote machine), read machine A and pull the user
data to be backed up onto the tape drive attached to B.  Ideally, we
would use BRMS to accomplish this task.  At this point - our main backup
concern is our user data, secondary is the system backup.  I am told we
are not concerned about bandwidth at this moment.  This issue is
currently in the process of resolution.  So, is this feasible to do with
BRMS or some other means?  Anybody have any 'how to' advice?

Thanks,

Adrienne McConnon       

Vercuity - Parsippany

-----Original Message-----
From: midrange-l-request@xxxxxxxxxxxx
[mailto:midrange-l-request@xxxxxxxxxxxx] 
Sent: Tuesday, February 27, 2007 11:51 AM
To: midrange-l@xxxxxxxxxxxx
Subject: MIDRANGE-L Digest, Vol 6, Issue 458

Send MIDRANGE-L mailing list submissions to
        midrange-l@xxxxxxxxxxxx

To subscribe or unsubscribe via the World Wide Web, visit
        http://lists.midrange.com/mailman/listinfo/midrange-l
or, via email, send a message with subject or body 'help' to
        midrange-l-request@xxxxxxxxxxxx

You can reach the person managing the list at
        midrange-l-owner@xxxxxxxxxxxx

When replying, please edit your Subject line so it is more specific than
"Re: Contents of MIDRANGE-L digest..."

*** NOTE: When replying to this digest message, PLEASE remove all text
unrelated to your reply and change the subject line so it is meaningful.

Today's Topics:

   1. Re: Call iSeries program from C# program (Bob O.)
   2. question about brms network backups (Adrienne McConnon)
   3. Re: Problem with a 6400 printer - use a UPS? (Jerry Adams)
   4. Re: How To Configure Console Address (Darrell A Martin)
   5. Re: question about brms network backups
      (smorrison@xxxxxxxxxxxxxxxxxxx)
   6. Re: Call iSeries program from C# program (Bob O.)
   7. Re: Problem with a 6400 printer - use a UPS? (Pat Barber)
   8. Re: How To Configure Console Address (rob@xxxxxxxxx)

----------------------------------------------------------------------

message: 1
date: Tue, 27 Feb 2007 10:32:00 -0600
from: "Bob O." <otis_the_cat@xxxxxxxxxxx>
subject: Re: Call iSeries program from C# program

   Thanks , its working great except for one thing....
   I'm testing this out in a web application as opposed to a Windows
GUI.

   I have the iSeries/As400/System i program being called in the
Page_Load
   event of the initial web page that opens (default.aspx).  It seems
that
   the Page_Load event fires no matter what happens (ie. clicking a
button). 
   I even added a class level boolean variable and change it to false
after
   the programs run.  If I click on a button (that has no code for it
yet)
   the Page_Load event fires, and then the Click event for the button.
When
   the page load runs, the boolean variable is automatically reset to
true
   and the AS400 programs are called again.

   Any way that you know of to get the programs to call only on the
first
   time the page is opened?

   Thanks.

----------------------------------------------------------------------

     From:  richard@xxxxxxxxxxx
     Reply-To:  Midrange Systems Technical Discussion
     <midrange-l@xxxxxxxxxxxx>
     To:  midrange-l@xxxxxxxxxxxx
     Subject:  Re: Call iSeries program from C# program
     Date:  Mon, 26 Feb 2007 18:02:59 -0600
     >Probably true if the iSeries program requires parameters :-)
     >
     >Even if parms are not used I think you need to define them and
pass
     >something when calling ExecuteNonQuery, even if it's blanks you're
     >passing.
     >
     >Glad it's working.
     >
     >Regards,
     >Richard Schoen
     >RJS Software Systems Inc.
     >"Providing Your....iNFORMATION NOW!"
     >Email: richard@xxxxxxxxxxxxxxx
     >Web Site: http://www.rjssoftware.com
     >Tel: (952) 898-3038
     >Fax: (952) 898-1781
     >Toll Free: (888) RJSSOFT
     >----------------------------------------
     >message: 5
     >date: Mon, 26 Feb 2007 12:34:08 -0600
     >from: "Bob O." <otis_the_cat@xxxxxxxxxxx>
     >subject: Re: Call iSeries program from C# program
     >
     >    It didn't like not having any parameters built for the
     >    "ExecuteNonQuery()".  I put in a null value and WhaLa!
     >--
     >This is the Midrange Systems Technical Discussion (MIDRANGE-L)
mailing
     list
     >To post a message email: MIDRANGE-L@xxxxxxxxxxxx
     >To subscribe, unsubscribe, or change list options,
     >visit: http://lists.midrange.com/mailman/listinfo/midrange-l
     >or email: MIDRANGE-L-request@xxxxxxxxxxxx
     >Before posting, please take a moment to review the archives
     >at http://archive.midrange.com/midrange-l.
     >

----------------------------------------------------------------------

   Win a Zune**make MSN(R) your homepage for your chance to win!

------------------------------

message: 2
date: Tue, 27 Feb 2007 09:32:32 -0700
from: "Adrienne McConnon" <Adrienne.McConnon@xxxxxxxxxxxx>
subject: question about brms network backups

Good morning!

Our scenario is - we have a new iSeries in the office, our BR machine is
now located miles away in a remote location.  The tape drive is attached
to the remote BR machine.  We would like to backup the new machine to
the remote tape drive/remote iSeries.  The 3 units are networked and
bandwidth is gong to be increased.

Is it possible to use BRMS to backup up the new machine to the remote
tape drive and or remote iseries?

How would one do this?

Thanks,

Adrienne McConnon    
Vercuity

------------------------------

message: 3
date: Tue, 27 Feb 2007 10:35:01 -0600
from: Jerry Adams <jerry@xxxxxxxxxxxxxxx>
subject: Re: Problem with a 6400 printer - use a UPS?

Pete,

I'm not familiar with the 6400 but we use the basic UPS for our HP
lasers and smaller.  We use the same UPS for some big honkers (Canon's
and Ricoh's).  We even use the same for our twinax printers because
spikes from power outages and *Immed restarts were blowing cards in
them.

        * Jerry C. Adams
*IBM System i5/iSeries Programmer/Analyst B&W Wholesale Distributors,
Inc.* * voice
        615.995.7024
fax
        615.995.1201
email
        jerry@xxxxxxxxxxxxxxx <mailto:jerry@xxxxxxxxxxxxxxx>

Pete Helgren wrote:

Yep.  I had them try the old tried and true "Turn off, wait, turn back

on" routine.  They have had problems with this before but we were able

to get them going again.

Just as an aside, is there such a thing as a UPS designed for a 
printer?  These folks have frequent power outages and surges (small 
island in S.E. Alaska).  The System i and x servers are well protected

and the twinax connected printers seems to weather these power outages

OK but this Ethernet attached printer seems to have the most problems.
If there is such a thing as a UPS designed for a line printer, these 
guys would be candidates.

Pete


Pat Barber wrote:

I' sure you told them to turn the printer off and back on ???
The power on sequence would reload any micro code needed for comm.

or

You have a ethernet card failure due to power surge.

Pete Helgren wrote:

My customer had a power failure this morning and ever since then, 
one of their printers, a model 6400 with  an Ethernet Interface,

cannot print.

I have ended the printer writer, varied off and on the device and 
restarted the writer.  The writer runs for several seconds and then 
ends abnormally with the following message in the job log:




------------------------------

message: 4
date: Tue, 27 Feb 2007 10:40:39 -0600
from: "Darrell A Martin" <DMartin@xxxxxxxxxxxxx>
subject: Re: How To Configure Console Address

Hi:

(I think the address to the original question depends on the device.)

Anyway, are you sure about the console having to be port 0 switch 0? We
have two 3196 devices set up to use as consoles. One is port 0 switch 0
and is on my desk, the other is port 0 switch 3 and is in the Computer
Room.
(Both devices are on Controller 6.) Yet, we have for years used the 0/3
device as "the" console, in some cases not even having the other one
connected for long stretches of time. I have not encountered any
function I could not do from the 0/3 terminal.

Looking for education. If there is a real difference, I might swap the
two.

Darrell

Darrell A. Martin  -  630-754-2141
Manager, Computer Operations
dmartin@xxxxxxxxxxxxx

midrange-l-bounces@xxxxxxxxxxxx wrote on 02/27/2007 10:08:22 AM:

The console must be plugged into port 0 and have an address of zero.
You need to go into setup mode and change the address of the device to

zero.

TacK wrote:

I have two consoles connected by TWINAX cable.
Promary console is port 0 and address 0 and secondary console is 
port 3 and address 3. address 1 and 2 is shared by printer.

Now the display of the primary console has been broken down and I 
need to replace the secondary console as a primary. I tried to 
pulgin the cable which is connedted to the primary and turned on the

console, but the console is recognized as port 0 and address 3.

Does anybody know how to configure the address on the console? or do

I have to IPL?






------------------------------

message: 5
date: Tue, 27 Feb 2007 10:41:44 -0600
from: smorrison@xxxxxxxxxxxxxxxxxxx
subject: Re: question about brms network backups

Before you jump into this remote backup possibility, check here to see
how large a connection you need to transfer your data:
http://www.ibeast.com/content/tools/band-calc.asp
We were interested in replicating tapes between our primary and backup
site, but the bandwidth made in impractical for us.

Are you using a data mirroring package? What we are trying to do is to
run the backups on the remote system. We will embed a command in the
data replication journals that tells the backup system to stop applying
journals to the backup system, and start the backup. When the backup is
complete, it tells the backup system to begin applying the journaled
data that hasn't been applied.


Steven Morrison
Fidelity Express
903-885-1283  ext. 479



"Adrienne McConnon" <Adrienne.McConnon@xxxxxxxxxxxx> 
Sent by: midrange-l-bounces@xxxxxxxxxxxx
02/27/2007 10:32 AM
Please respond to
Midrange Systems Technical Discussion <midrange-l@xxxxxxxxxxxx>


To
<MIDRANGE-L@xxxxxxxxxxxx>
cc

Subject
question about brms network backups






Good morning!
 
Our scenario is - we have a new iSeries in the office, our BR machine is
now located miles away in a remote location.  The tape drive is attached
to the remote BR machine.  We would like to backup the new machine to
the remote tape drive/remote iSeries.  The 3 units are networked and
bandwidth is gong to be increased.
 
Is it possible to use BRMS to backup up the new machine to the remote
tape drive and or remote iseries?
 
How would one do this?
 
Thanks,
 
Adrienne McConnon 
Vercuity