RE: Printer error

Try the *IBMSNMPDRV instead of the PJL driver?

Eric DeLong
Sally Beauty Company
MIS-Project Manager (BSG)
940-898-7863 or ext. 1863



-----Original Message-----
From: Mark Allen [mailto:mallen@xxxxxxxx]
Sent: Thursday, May 15, 2003 1:26 PM
To: 'Midrange Systems Technical Discussion'
Subject: RE: Printer error


Per Konica with the Net Fusion card it will support IPDS

Can't use rmtoutq need to be able to start/reprint at specific page

It works for a while like 50-60 pages that hangs

-----Original Message-----
From: midrange-l-bounces@xxxxxxxxxxxx
[mailto:midrange-l-bounces@xxxxxxxxxxxx] On Behalf Of Jim Franz
Sent: Thursday, May 15, 2003 2:20 PM
To: Midrange Systems Technical Discussion
Subject: Re: Printer error


if the printer does not support PJL, then you cannot use *lan. that will
cause the "communication error". Try rmtoutq. jim

----- Original Message -----
From: "Mark Allen" <mallen@xxxxxxxx>
To: "'Midrange Systems Technical Discussion'" <midrange-l@xxxxxxxxxxxx>
Sent: Thursday, May 15, 2003 1:42 PM
Subject: RE: Printer error


> Force 75
>
> *lan
>
> Did find one thing in IBM Knowledge base about possible problem if 
> printer time out lower than AS/400 TCP Keep alive value, changed the 
> printer to be higher, testing now
>
> -----Original Message-----
> From: midrange-l-bounces@xxxxxxxxxxxx 
> [mailto:midrange-l-bounces@xxxxxxxxxxxx] On Behalf Of Jim Franz
> Sent: Thursday, May 15, 2003 1:24 PM
> To: Midrange Systems Technical Discussion
> Subject: Re: Printer error
>
>
> Which Konica?
> Knowlege Base doc lists Konica 7150 does not support PJL, so are you 
> using *lan or rmtoutq config? jim
>
> ----- Original Message -----
> From: "Mark Allen" <mallen@xxxxxxxx>
> To: "'Midrange Systems Technical Discussion'" 
> <midrange-l@xxxxxxxxxxxx>
> Sent: Thursday, May 15, 2003 12:52 PM
> Subject: RE: Printer error
>
>
> > Yeah looked there nothing excep started, did not end normally
> >
> > -----Original Message-----
> > From: midrange-l-bounces@xxxxxxxxxxxx 
> > [mailto:midrange-l-bounces@xxxxxxxxxxxx] On Behalf Of Carl Galgano
> > Sent: Thursday, May 15, 2003 12:43 PM
> > To: 'Midrange Systems Technical Discussion'
> > Subject: RE: Printer error
> >
> >
> > Did you check the joblog of the writer job.  I think if you do a 
> > wrkjob PRTF75 you should show the writer job.  Take a look at it's 
> > job
>
> > log for more info. cjg
> >
> > Carl J. Galgano
> > EDI Consulting Services, Inc.
> > 550 Kennesaw Avenue, Suite 800
> > Marietta, GA  30060
> > (770) 422-2995 - voice
> > (419) 730-8212 - fax
> > mailto:cgalgano@xxxxxxxxxxxxxxxxx http://www.ediconsulting.com AS400

> > EDI, Networking, E-Commerce and Communications Consulting and 
> > Implementation http://www.icecreamovernight.com
> > Premium Ice Cream Brands shipped Overnight
> >
> > "You ain't gonna learn what you don't want to know" - rw
> >
> > -----Original Message-----
> > From: midrange-l-bounces@xxxxxxxxxxxx 
> > [mailto:midrange-l-bounces@xxxxxxxxxxxx] On Behalf Of Mark Allen
> > Sent: Thursday, May 15, 2003 11:51 AM
> > To: midrange-l@xxxxxxxxxxxx
> > Subject: Printer error
> >
> >
> > Anyone know where I can find what the error code 20 really means. 
> > Obviously 20-39 mean different things but where can I find what they

> > are?
> >
> >                          Additional Message Information
> >
> >
> >
> >  Message ID . . . . . . :   PQT3621       Severity . . . . . . . :
> 40
> >
> >  Message type . . . . . :   Information
> >
> >  Date sent  . . . . . . :   05/15/03      Time sent  . . . . . . :
> > 11:44:30
> >
> >
> >  Message . . . . :   The session with device PRTF75 ended
abnormally.
> >
> >  Cause . . . . . :   The session with device PRTF75 at RMTLOCNAME
> >
> >    207.144.134.232, using PORT 5001, ended abnormally.  The error 
> > code
>
> > is 20,
> >    which indicates one of the following conditions:
> >
> >      20-39: A communications failure occurred.
> >
> >      40-59: An internal failure occurred.
> >
> >  Recovery  . . . :   For error codes 20-39, check for problems in
your
> > network.
> >    After correcting the problem, start the printer writer to begin 
> > processing
> >    files again. If the problem continues, report it using the ANZPRB

> > command.
> >    For error codes 40-59, start the printer writer again. If the 
> > problem
> >
> >    continues, report it using the ANZPRB command.
> >
> >  Technical description . . . . . . . . :   The internal message
> > identifier (ID)
> >
> > More...
> >  Press Enter to continue.
> >
> >
> >
> >  F3=Exit   F6=Print   F9=Display message details   F12=Cancel
> >
> >  F21=Select assistance level
> >
> >
> >
> >
> > Mark Allen
> > IS Manager
> > Wilkes Telephone & Electric
> > 11 W. Court Street
> > Washington, GA 30673
> > Phone: (706) 678-9565
> > Fax: (706) 678-1000
> >
> >
> > _______________________________________________
> > This is the Midrange Systems Technical Discussion (MIDRANGE-L) 
> > mailing
>
> > list To post a message email: MIDRANGE-L@xxxxxxxxxxxx To subscribe, 
> > unsubscribe, or change list options,
> > visit: http://lists.midrange.com/mailman/listinfo/midrange-l
> > or email: MIDRANGE-L-request@xxxxxxxxxxxx
> > Before posting, please take a moment to review the archives at 
> > http://archive.midrange.com/midrange-l.
> >
> >
> > _______________________________________________
> > This is the Midrange Systems Technical Discussion (MIDRANGE-L) 
> > mailing
>
> > list To post a message email: MIDRANGE-L@xxxxxxxxxxxx To subscribe, 
> > unsubscribe, or change list options,
> > visit: http://lists.midrange.com/mailman/listinfo/midrange-l
> > or email: MIDRANGE-L-request@xxxxxxxxxxxx
> > Before posting, please take a moment to review the archives at 
> > http://archive.midrange.com/midrange-l.
> >
> > _______________________________________________
> > This is the Midrange Systems Technical Discussion (MIDRANGE-L) 
> > mailing
> list
> > To post a message email: MIDRANGE-L@xxxxxxxxxxxx
> > To subscribe, unsubscribe, or change list options,
> > visit: http://lists.midrange.com/mailman/listinfo/midrange-l
> > or email: MIDRANGE-L-request@xxxxxxxxxxxx
> > Before posting, please take a moment to review the archives at 
> > http://archive.midrange.com/midrange-l.
> >
> >
>
>
> _______________________________________________
> This is the Midrange Systems Technical Discussion (MIDRANGE-L) mailing

> list To post a message email: MIDRANGE-L@xxxxxxxxxxxx To subscribe, 
> unsubscribe, or change list options,
> visit: http://lists.midrange.com/mailman/listinfo/midrange-l
> or email: MIDRANGE-L-request@xxxxxxxxxxxx
> Before posting, please take a moment to review the archives at 
> http://archive.midrange.com/midrange-l.
>
> _______________________________________________
> This is the Midrange Systems Technical Discussion (MIDRANGE-L) mailing
list
> To post a message email: MIDRANGE-L@xxxxxxxxxxxx
> To subscribe, unsubscribe, or change list options,
> visit: http://lists.midrange.com/mailman/listinfo/midrange-l
> or email: MIDRANGE-L-request@xxxxxxxxxxxx
> Before posting, please take a moment to review the archives at 
> http://archive.midrange.com/midrange-l.
>
>


_______________________________________________
This is the Midrange Systems Technical Discussion (MIDRANGE-L) mailing
list To post a message email: MIDRANGE-L@xxxxxxxxxxxx To subscribe,
unsubscribe, or change list options,
visit: http://lists.midrange.com/mailman/listinfo/midrange-l
or email: MIDRANGE-L-request@xxxxxxxxxxxx
Before posting, please take a moment to review the archives
at http://archive.midrange.com/midrange-l.

_______________________________________________
This is the Midrange Systems Technical Discussion (MIDRANGE-L) mailing list
To post a message email: MIDRANGE-L@xxxxxxxxxxxx
To subscribe, unsubscribe, or change list options,
visit: http://lists.midrange.com/mailman/listinfo/midrange-l
or email: MIDRANGE-L-request@xxxxxxxxxxxx
Before posting, please take a moment to review the archives
at http://archive.midrange.com/midrange-l.