RE: Printer Help...Ricoh Aficio 700 Setup..

You were right...

I http'd into your printer, and looked at it's port setting...  it was
10000,  I tried to change it to, 9099, but I didn't have the password, so
after reading the documents, it said the 9099 was just -1 from in the device
call, so I changed my devd from 9100 to 10001 and tah-dah, it worked...

Thanks... I'll change things back to 9100, when I get a password, but at
least for now, I might have my dissapearing prints solved..

Tim

> -----Original Message-----
> From: DeLong, Eric [SMTP:EDeLong@xxxxxxxxxxxxxxx]
> Sent: Thursday, April 10, 2003 10:38 AM
> To:   'Midrange Systems Technical Discussion'
> Subject:      RE: Printer Help...Ricoh Aficio 700 Setup..
> 
> Tim,
> 
> >From Ricoh's site, that printer uses a "Fiery EB-70 Print Controller".
> You
> might find something more specific.  It seems this controller might
> respond
> to SNMP driver, so perhaps:
> 
> http://www-912.ibm.com/s_dir/slkbase.NSF/acf2ee1e9d64b16e8625680b00020389/
> 94
> e73364f979e388862569030071c398?OpenDocument&ExpandSection=3,7,6,5&Highligh
> t=
> 0,fiery#_Section3
> 
> 
> I did run across this in another document, too:
> <snip>
> Osicom, Ricoh, and Savin print servers support bidirectional PJL. However,
> the Base Port Number must be changed to 9099 on the NIC card or print
> server. Once this is done, the *LAN 3812 PJL device description can be set
> up to use port 9100 on the Osicom, Ricoh and Savin internal NIC cards, or
> ports 9100, 9101 and 9102 for external Osicom NetPrint print servers
> (depending on which parallel port is being used). The Base Port Number can
> be changed using an Internet browser (such as Microsoft Internet Explorer
> or
> Netscape Navigator) using the Web interface for the print server. For
> example, link to "http://38.242.136.182/"; where 38.242.136.182 is the IP
> address for the print server.
> <snip> 
> 
> Eric DeLong
> Sally Beauty Company
> MIS-Project Manager (BSG)
> 940-898-7863 or ext. 1863
> 
> 
> 
> -----Original Message-----
> From: Hatzenbeler, Tim [mailto:thatzenbeler@xxxxxxxxxxxxx]
> Sent: Thursday, April 10, 2003 11:53 AM
> To: 'Midrange Systems Technical Discussion'
> Subject: Printer Help...Ricoh Aficio 700 Setup..
> 
> 
> Printer Help...Ricoh Aficio 700 Setup..
> 
> 
> I was wondering if any one, might have a  'wrkdevd' config for this
> printer... It's connected directly into our IP network, and for some
> reason,
> I can print to it, using a rmtprtwtr,  but when I tried to give it, it's
> own
> devd, it doesn't seem to work, I get a msgw, that can't be answered with a
> reply...  something about, not being availabe..  and the device is varied
> on, and I did strprtwtr, and it is sitting with a rls/wtr status...
> 
> This printer is the ricoh photocopier model...
> 
> Thanks, tim
> 
> This e-mail message, including any attachments, is for the sole use of the
> intended recipient(s) and may contain confidential or privileged
> information.  Any unauthorized review, use, disclosure or distribution is
> prohibited.  If you are not the intended recipient, please contact the
> sender by reply e-mail and destroy the message.
> _______________________________________________
> This is the Midrange Systems Technical Discussion (MIDRANGE-L) mailing
> list
> To post a message email: MIDRANGE-L@xxxxxxxxxxxx
> To subscribe, unsubscribe, or change list options,
> visit: http://lists.midrange.com/mailman/listinfo/midrange-l
> or email: MIDRANGE-L-request@xxxxxxxxxxxx
> Before posting, please take a moment to review the archives
> at http://archive.midrange.com/midrange-l.
> 
> 
> _______________________________________________
> This is the Midrange Systems Technical Discussion (MIDRANGE-L) mailing
> list
> To post a message email: MIDRANGE-L@xxxxxxxxxxxx
> To subscribe, unsubscribe, or change list options,
> visit: http://lists.midrange.com/mailman/listinfo/midrange-l
> or email: MIDRANGE-L-request@xxxxxxxxxxxx
> Before posting, please take a moment to review the archives
> at http://archive.midrange.com/midrange-l.
This e-mail message, including any attachments, is for the sole use of the
intended recipient(s) and may contain confidential or privileged
information.  Any unauthorized review, use, disclosure or distribution is
prohibited.  If you are not the intended recipient, please contact the
sender by reply e-mail and destroy the message.