|
midrange.com
Hmmm. That's an interesting concept, Joan. I do that personally for my
printouts, but for the most part, my users can't view print queues
(security). I may have to consider that for some people, however. Some of
them CAN view print queues, at least, their own.
Konrad, I upgraded from a 720 with 420 CPW to a single processor 270 with
1050 CPW, and my users got worried that their jobs weren't running - they
finished so fast. If I had a dual processor 270 - I don't know what we'd
do.... BTW, 1 hour cycle for MPSP, MRP, and post-MRP reports - was 2.5
hours on the 720, 4 hours on the 500, and so on.
The only pther problem was when I unpacked the 270, my boss was in the
computer room and he said "Why do we have this big IT department when that
little thing runs the whole plant?". I have PC servers bigger than the
270....... and I don't even want to talk about the Liebert air
conditioner.....
Dale @ Fleetwood
"McCready, Joan"
<Joan.McCready@xxxxx To: "'MAPICS ERP System
Discussion'" <mapics-l@xxxxxxxxxxxx>
tekint.com> cc:
Sent by: Subject: RE: Moving jobs
from JQ to JQ
mapics-l-bounces@xxx
range.com
04/02/2003 04:16 PM
Please respond to
MAPICS ERP System
Discussion
Konrad,
Yeh, yeh, yeh - rub it in, why don't cha! BTW, we have all our printer
output go to a queue with no printer attached. My users only print what is
needed (saves a few zill-i-on trees that way!).
Jealously, Joan
Joan McCready, IS Manager phone: 636-479-4499
MetalTek International fax: 636-479-3399
The Carondelet Division www.metaltekint.com
8600 Commercial Blvd
Pevely, MO 63070
-----Original Message-----
From: Konrad Underkofler [mailto:kdunderk@xxxxxxxxxxxxx]
Sent: Wednesday, April 02, 2003 2:38 PM
To: 'MAPICS ERP System Discussion'
Subject: RE: Moving jobs from JQ to JQ
Just to rub it in a bit since we upgraded to our dual processor 270 it is
tough to ever find a job in a queue to move and we rarely ever get a
conflict. Trying to trap printer output is a real challenge.
To make sure the system is still running and to have something to watch we
kick off a few MRP runs. j/k of course :)
Seriously if you do have any long running reports that you want to run
outside the MAPICS job control system find the CL that runs the job and
strip out the AMZ activity to the JOBACT file. Then you can run them
anywhere you want. Otherwise be very careful. Note that the Synon apps
pretty much have their own control system so they are less sensitive.
Regards
Konrad
-----Original Message-----
From: Eric Wolf [mailto:eric_a_wolf@xxxxxxxxxxx]
Sent: Wednesday, April 02, 2003 3:03 PM
To: MAPICS ERP System Discussion
Subject: Re: Moving jobs from JQ to JQ
Thanks to all...
I just wanted to make sure...
Eric
----- Original Message -----
From: <Bob.Voltz@xxxxxxxxxxxxxx>
To: "MAPICS ERP System Discussion" <mapics-l@xxxxxxxxxxxx>
Sent: Wednesday, April 02, 2003 11:29 AM
Subject: Re: Moving jobs from JQ to JQ
>
>
>
>
>
> You will probably be inundated with replies to this one.
>
> AFAIK you cannot move MAPICS jobq jobs.
> The jobq is part of the JOBACT record and if they don't match, the job
will
> bomb.
>
> Bob Voltz
> Biomet
>
> _______________________________________________
> This is the MAPICS ERP System Discussion (MAPICS-L) mailing list To
> post a message email: MAPICS-L@xxxxxxxxxxxx To subscribe, unsubscribe,
> or change list options,
> visit: http://lists.midrange.com/mailman/listinfo/mapics-l
> or email: MAPICS-L-request@xxxxxxxxxxxx
> Before posting, please take a moment to review the archives at
> http://archive.midrange.com/mapics-l.
>
>
_______________________________________________
This is the MAPICS ERP System Discussion (MAPICS-L) mailing list To post a
message email: MAPICS-L@xxxxxxxxxxxx To subscribe, unsubscribe, or change
list options,
visit: http://lists.midrange.com/mailman/listinfo/mapics-l
or email: MAPICS-L-request@xxxxxxxxxxxx
Before posting, please take a moment to review the archives
at http://archive.midrange.com/mapics-l.
_______________________________________________
This is the MAPICS ERP System Discussion (MAPICS-L) mailing list To post a
message email: MAPICS-L@xxxxxxxxxxxx To subscribe, unsubscribe, or change
list options,
visit: http://lists.midrange.com/mailman/listinfo/mapics-l
or email: MAPICS-L-request@xxxxxxxxxxxx
Before posting, please take a moment to review the archives
at http://archive.midrange.com/mapics-l.
_______________________________________________
This is the MAPICS ERP System Discussion (MAPICS-L) mailing list
To post a message email: MAPICS-L@xxxxxxxxxxxx
To subscribe, unsubscribe, or change list options,
visit: http://lists.midrange.com/mailman/listinfo/mapics-l
or email: MAPICS-L-request@xxxxxxxxxxxx
Before posting, please take a moment to review the archives
at http://archive.midrange.com/mapics-l.
As an Amazon Associate we earn from qualifying purchases.
This mailing list archive is Copyright 1997-2024 by midrange.com and David Gibbs as a compilation work. Use of the archive is restricted to research of a business or technical nature. Any other uses are prohibited. Full details are available on our policy page. If you have questions about this, please contact [javascript protected email address].
Operating expenses for this site are earned using the Amazon Associate program and Google Adsense.
